CatOS - Int details

Answered Question
May 19th, 2010
User Badges:

Hi


Not much familiar with CATOS


what command allows to check interface details on CATOS, module #1 48 port 10/100/1000

I m interested in getting details for int giga 1/5

Correct Answer by Giuseppe Larosa about 7 years 1 week ago

Hello Saquib,


sh port 1/5


additional counters are reported in


sh mac 1/5


example:



sh port 2/5

* = Configured MAC Address


Port  Name               Status     Vlan       Level  Duplex Speed Type

----- ------------------ ---------- ---------- ------ ------ ----- ------------

2/5  ptocern404pp1224   connected  605        normal a-full a-1Gb 10/100/1000


Port  AuxiliaryVlan AuxVlan-Status

----- ------------- --------------

2/5  none          none         



Port  Security Violation Shutdown-Time Age-Time Max-Addr Trap     IfIndex

----- -------- --------- ------------- -------- -------- -------- -------

2/5  disabled  shutdown             0        0        1 disabled     353


Port  Num-Addr Secure-Src-Addr     Age-Left Last-Src-Addr     Shutdown/Time-Left

----- -------- -----------------   -------- ----------------- ------------------

2/5         0                 -          -                 -        -         -


Port  Flooding on Address Limit

----- -------------------------

2/5                    Enabled


Port  Send FlowControl  Receive FlowControl   RxPause    TxPause    Unsupported

      admin    oper     admin     oper                              opcodes

----- -------- -------- --------- ---------   ---------- ---------- -----------

2/5  on       disagree desired   off         0          0          0        


Port   Admin Channel LACP Port  Ch   Partner Oper                    Partner

       key   Mode    Priority   id   Sys ID                          Port

------ ----- ------- --------- ---- -------------------------------- -------

2/5    718  passive    128       0      0:00-00-00-00-00-00            0


Port  Status      ErrDisable Reason    Port ErrDisableTimeout  Action on Timeout

----  ----------  -------------------  ----------------------  -----------------

2/5  connected                     -  Enable                  No Change


Port  Align-Err  FCS-Err    Xmit-Err   Rcv-Err    UnderSize

----- ---------- ---------- ---------- ---------- ---------

2/5           -          0          0      32127         0


Port  Single-Col Multi-Coll Late-Coll  Excess-Col Carri-Sen Runts     Giants

----- ---------- ---------- ---------- ---------- --------- --------- ---------

2/5           0          0          0          0         0         0         0


Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27



sh mac 2/5


Port     Rcv-Unicast          Rcv-Multicast        Rcv-Broadcast

-------- -------------------- -------------------- --------------------

2/5               2701929405                    0              2457154


Port     Xmit-Unicast         Xmit-Multicast       Xmit-Broadcast

-------- -------------------- -------------------- --------------------

2/5                680508948             19331294               746433


Port     Rcv-Octet            Xmit-Octet

-------- -------------------- --------------------

2/5            3993868326093         103277529193


MAC      Dely-Exced MTU-Exced  In-Discard Lrn-Discrd In-Lost    Out-Lost

-------- ---------- ---------- ---------- ---------- ---------- ----------

2/5              0          0      32127          0          0          0


Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27


Hope to help

Giuseppe

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Jon Marshall Wed, 05/19/2010 - 07:07
User Badges:
  • Super Blue, 32500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

saquib.tandel wrote:


Hi


Not much familiar with CATOS


what command allows to check interface details on CATOS, module #1 48 port 10/100/1000

I m interested in getting details for int giga 1/5


From memory -


"sh port 1/5"  should do it.


Jon

pciaccio Wed, 05/19/2010 - 07:08
User Badges:
  • Silver, 250 points or more

Use the "SHOW PORT" command for port details.  The SHOW PORT COUNTERS is another good one. So for your example it will be "SHOW PORT 1/5".. Good Luck..

Correct Answer
Giuseppe Larosa Wed, 05/19/2010 - 07:19
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

Hello Saquib,


sh port 1/5


additional counters are reported in


sh mac 1/5


example:



sh port 2/5

* = Configured MAC Address


Port  Name               Status     Vlan       Level  Duplex Speed Type

----- ------------------ ---------- ---------- ------ ------ ----- ------------

2/5  ptocern404pp1224   connected  605        normal a-full a-1Gb 10/100/1000


Port  AuxiliaryVlan AuxVlan-Status

----- ------------- --------------

2/5  none          none         



Port  Security Violation Shutdown-Time Age-Time Max-Addr Trap     IfIndex

----- -------- --------- ------------- -------- -------- -------- -------

2/5  disabled  shutdown             0        0        1 disabled     353


Port  Num-Addr Secure-Src-Addr     Age-Left Last-Src-Addr     Shutdown/Time-Left

----- -------- -----------------   -------- ----------------- ------------------

2/5         0                 -          -                 -        -         -


Port  Flooding on Address Limit

----- -------------------------

2/5                    Enabled


Port  Send FlowControl  Receive FlowControl   RxPause    TxPause    Unsupported

      admin    oper     admin     oper                              opcodes

----- -------- -------- --------- ---------   ---------- ---------- -----------

2/5  on       disagree desired   off         0          0          0        


Port   Admin Channel LACP Port  Ch   Partner Oper                    Partner

       key   Mode    Priority   id   Sys ID                          Port

------ ----- ------- --------- ---- -------------------------------- -------

2/5    718  passive    128       0      0:00-00-00-00-00-00            0


Port  Status      ErrDisable Reason    Port ErrDisableTimeout  Action on Timeout

----  ----------  -------------------  ----------------------  -----------------

2/5  connected                     -  Enable                  No Change


Port  Align-Err  FCS-Err    Xmit-Err   Rcv-Err    UnderSize

----- ---------- ---------- ---------- ---------- ---------

2/5           -          0          0      32127         0


Port  Single-Col Multi-Coll Late-Coll  Excess-Col Carri-Sen Runts     Giants

----- ---------- ---------- ---------- ---------- --------- --------- ---------

2/5           0          0          0          0         0         0         0


Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27



sh mac 2/5


Port     Rcv-Unicast          Rcv-Multicast        Rcv-Broadcast

-------- -------------------- -------------------- --------------------

2/5               2701929405                    0              2457154


Port     Xmit-Unicast         Xmit-Multicast       Xmit-Broadcast

-------- -------------------- -------------------- --------------------

2/5                680508948             19331294               746433


Port     Rcv-Octet            Xmit-Octet

-------- -------------------- --------------------

2/5            3993868326093         103277529193


MAC      Dely-Exced MTU-Exced  In-Discard Lrn-Discrd In-Lost    Out-Lost

-------- ---------- ---------- ---------- ---------- ---------- ----------

2/5              0          0      32127          0          0          0


Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27


Hope to help

Giuseppe

Actions

This Discussion