Solved: CatOS - Int details

saquib.tandel · ‎05-19-2010

Hi

Not much familiar with CATOS

what command allows to check interface details on CATOS, module #1 48 port 10/100/1000

I m interested in getting details for int giga 1/5

Giuseppe Larosa · ‎05-19-2010

Hello Saquib,

sh port 1/5

additional counters are reported in

sh mac 1/5

example:

sh port 2/5

* = Configured MAC Address

Port Name Status Vlan Level Duplex Speed Type

----- ------------------ ---------- ---------- ------ ------ ----- ------------

2/5 ptocern404pp1224 connected 605 normal a-full a-1Gb 10/100/1000

Port AuxiliaryVlan AuxVlan-Status

----- ------------- --------------

2/5 none none

Port Security Violation Shutdown-Time Age-Time Max-Addr Trap IfIndex

----- -------- --------- ------------- -------- -------- -------- -------

2/5 disabled shutdown 0 0 1 disabled 353

Port Num-Addr Secure-Src-Addr Age-Left Last-Src-Addr Shutdown/Time-Left

----- -------- ----------------- -------- ----------------- ------------------

2/5 0 - - - - -

Port Flooding on Address Limit

----- -------------------------

2/5 Enabled

Port Send FlowControl Receive FlowControl RxPause TxPause Unsupported

admin oper admin oper opcodes

----- -------- -------- --------- --------- ---------- ---------- -----------

2/5 on disagree desired off 0 0 0

Port Admin Channel LACP Port Ch Partner Oper Partner

key Mode Priority id Sys ID Port

------ ----- ------- --------- ---- -------------------------------- -------

2/5 718 passive 128 0 0:00-00-00-00-00-00 0

Port Status ErrDisable Reason Port ErrDisableTimeout Action on Timeout

---- ---------- ------------------- ---------------------- -----------------

2/5 connected - Enable No Change

Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize

----- ---------- ---------- ---------- ---------- ---------

2/5 - 0 0 32127 0

Port Single-Col Multi-Coll Late-Coll Excess-Col Carri-Sen Runts Giants

----- ---------- ---------- ---------- ---------- --------- --------- ---------

2/5 0 0 0 0 0 0 0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

sh mac 2/5

Port Rcv-Unicast Rcv-Multicast Rcv-Broadcast

-------- -------------------- -------------------- --------------------

2/5 2701929405 0 2457154

Port Xmit-Unicast Xmit-Multicast Xmit-Broadcast

-------- -------------------- -------------------- --------------------

2/5 680508948 19331294 746433

Port Rcv-Octet Xmit-Octet

-------- -------------------- --------------------

2/5 3993868326093 103277529193

MAC Dely-Exced MTU-Exced In-Discard Lrn-Discrd In-Lost Out-Lost

-------- ---------- ---------- ---------- ---------- ---------- ----------

2/5 0 0 32127 0 0 0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

Hope to help

Giuseppe

View solution in original post

Jon Marshall · ‎05-19-2010

saquib.tandel wrote:

Hi

Not much familiar with CATOS

what command allows to check interface details on CATOS, module #1 48 port 10/100/1000

I m interested in getting details for int giga 1/5

From memory -

"sh port 1/5" should do it.

Jon

pciaccio · ‎05-19-2010

Use the "SHOW PORT" command for port details. The SHOW PORT COUNTERS is another good one. So for your example it will be "SHOW PORT 1/5".. Good Luck..

Giuseppe Larosa · ‎05-19-2010

Hello Saquib,

sh port 1/5

additional counters are reported in

sh mac 1/5

example:

sh port 2/5

* = Configured MAC Address

Port Name Status Vlan Level Duplex Speed Type

----- ------------------ ---------- ---------- ------ ------ ----- ------------

2/5 ptocern404pp1224 connected 605 normal a-full a-1Gb 10/100/1000

Port AuxiliaryVlan AuxVlan-Status

----- ------------- --------------

2/5 none none

Port Security Violation Shutdown-Time Age-Time Max-Addr Trap IfIndex

----- -------- --------- ------------- -------- -------- -------- -------

2/5 disabled shutdown 0 0 1 disabled 353

Port Num-Addr Secure-Src-Addr Age-Left Last-Src-Addr Shutdown/Time-Left

----- -------- ----------------- -------- ----------------- ------------------

2/5 0 - - - - -

Port Flooding on Address Limit

----- -------------------------

2/5 Enabled

Port Send FlowControl Receive FlowControl RxPause TxPause Unsupported

admin oper admin oper opcodes

----- -------- -------- --------- --------- ---------- ---------- -----------

2/5 on disagree desired off 0 0 0

Port Admin Channel LACP Port Ch Partner Oper Partner

key Mode Priority id Sys ID Port

------ ----- ------- --------- ---- -------------------------------- -------

2/5 718 passive 128 0 0:00-00-00-00-00-00 0

Port Status ErrDisable Reason Port ErrDisableTimeout Action on Timeout

---- ---------- ------------------- ---------------------- -----------------

2/5 connected - Enable No Change

Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize

----- ---------- ---------- ---------- ---------- ---------

2/5 - 0 0 32127 0

Port Single-Col Multi-Coll Late-Coll Excess-Col Carri-Sen Runts Giants

----- ---------- ---------- ---------- ---------- --------- --------- ---------

2/5 0 0 0 0 0 0 0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

sh mac 2/5

Port Rcv-Unicast Rcv-Multicast Rcv-Broadcast

-------- -------------------- -------------------- --------------------

2/5 2701929405 0 2457154

Port Xmit-Unicast Xmit-Multicast Xmit-Broadcast

-------- -------------------- -------------------- --------------------

2/5 680508948 19331294 746433

Port Rcv-Octet Xmit-Octet

-------- -------------------- --------------------

2/5 3993868326093 103277529193

MAC Dely-Exced MTU-Exced In-Discard Lrn-Discrd In-Lost Out-Lost

-------- ---------- ---------- ---------- ---------- ---------- ----------

2/5 0 0 32127 0 0 0

Last-Time-Cleared

--------------------------

Fri May 29 2009, 12:06:27

Hope to help

Giuseppe