VIC2-2FXO and VIC2-2FXS on cisco 2801

Unanswered Question
May 18th, 2010

Hello,

I am having Cisco 2801 router with IOS "c2801-ipvoicek9-mz.124-20.T5.bin", i have installed VIC2-FXO on slot 2 [ this slot accepts only WICs and VICs] and VIC2-2FXS on slot0 [This slot only accepts VICs]

but the problem is that they both are not showing in show run and  show voice port summmary command.

i issued command show diag and found the below out for both slot:

VIC Slot 0:

        FXS Voice daughter card (2 port)

        WIC module not supported/disabled in this slot

        Hardware revision 1.1           Board revision B0

        Serial number     27276672      Part number    800-02493-04

        FRU Part Number     VIC-2FXS=

        Test history      0x0           RMA number     00-00-00

        Connector type    Wan Module

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 0E 01 01 01 A0 35 80 50 09 BD 04 00 00 00 00

          0x30: 58 00 00 00 01 12 27 01 FF FF FF FF FF FF FF FF

        WIC/VIC/HWIC Slot 1:

        4 Port FE Switch

        Base MAC Address         : 001a.6d50.cbfc

        MAC Address block size   : 4

        PCB Serial Number        : FOC10484E9S

        Hardware Revision        : 6.0

        Part Number              : 73-8474-06

        Board Revision           : A0

        Top Assy. Part Number    : 800-24193-02

        Deviation Number         : 0

        Fab Version              : 05

        CLEI Code                : IPUIA00RAA

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : HWIC-4ESW

        Version Identifier       : V01

        Connector Type           : 01

        EEPROM format version 4

        EEPROM contents (hex):

          0x00: 04 FF CF 06 00 1A 6D 50 CB FC 43 00 04 C1 8B 46

          0x10: 4F 43 31 30 34 38 34 45 39 53 40 00 56 41 06 00

          0x20: 82 49 21 1A 06 42 41 30 C0 46 03 20 00 5E 81 02

          0x30: 88 00 00 00 00 02 05 C6 8A 49 50 55 49 41 30 30

          0x40: 52 41 41 03 00 81 00 00 00 00 04 00 CB 89 48 57

          0x50: 49 43 2D 34 45 53 57 89 56 30 31 20 D9 02 C1 40

          0x60: 05 01 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

        WIC/VIC Slot 2:

        FXO Voice daughter card (2 port)

        Unknown EEPROM ver 16

        EEPROM format version 16

        EEPROM contents (hex):

          0x20: 10 0D 01 01 01 A0 C2 85 50 09 BF 01 00 00 00 00

          0x30: A0 00 00 00 02 01 09 01 FF FF FF FF FF FF FF FF

        WIC/VIC/HWIC Slot 3:

        Serial 2T (12in1)

        Hardware revision 1.0           Board revision D0

        Serial number     35386517      Part number    800-03181-01

        FRU Part Number     WIC-2T=

        Test history      0x0           RMA number     00-00-00

        Connector type    PCI

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 12 01 00 02 1B F4 95 50 0C 6D 01 00 00 00 00

          0x30: 68 00 00 00 00 09 02 00 FF FF FF FF FF FF FF FF

please help!

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
zafar12233 Wed, 05/19/2010 - 22:36

Hi,

I have managed to arrange the IOS "c2801-ipvoicek9-mz.124-20.T5.bin", but still the same problem.

please help!

Actions

This Discussion