05-18-2010 03:36 AM - edited 03-15-2019 10:48 PM
Hello,
I am having Cisco 2801 router with IOS "c2801-ipvoicek9-mz.124-20.T5.bin", i have installed VIC2-FXO on slot 2 [ this slot accepts only WICs and VICs] and VIC2-2FXS on slot0 [This slot only accepts VICs]
but the problem is that they both are not showing in show run and show voice port summmary command.
i issued command show diag and found the below out for both slot:
VIC Slot 0:
FXS Voice daughter card (2 port)
WIC module not supported/disabled in this slot
Hardware revision 1.1 Board revision B0
Serial number 27276672 Part number 800-02493-04
FRU Part Number VIC-2FXS=
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0E 01 01 01 A0 35 80 50 09 BD 04 00 00 00 00
0x30: 58 00 00 00 01 12 27 01 FF FF FF FF FF FF FF FF
WIC/VIC/HWIC Slot 1:
4 Port FE Switch
Base MAC Address : 001a.6d50.cbfc
MAC Address block size : 4
PCB Serial Number : FOC10484E9S
Hardware Revision : 6.0
Part Number : 73-8474-06
Board Revision : A0
Top Assy. Part Number : 800-24193-02
Deviation Number : 0
Fab Version : 05
CLEI Code : IPUIA00RAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-4ESW
Version Identifier : V01
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF CF 06 00 1A 6D 50 CB FC 43 00 04 C1 8B 46
0x10: 4F 43 31 30 34 38 34 45 39 53 40 00 56 41 06 00
0x20: 82 49 21 1A 06 42 41 30 C0 46 03 20 00 5E 81 02
0x30: 88 00 00 00 00 02 05 C6 8A 49 50 55 49 41 30 30
0x40: 52 41 41 03 00 81 00 00 00 00 04 00 CB 89 48 57
0x50: 49 43 2D 34 45 53 57 89 56 30 31 20 D9 02 C1 40
0x60: 05 01 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC/VIC Slot 2:
FXO Voice daughter card (2 port)
Unknown EEPROM ver 16
EEPROM format version 16
EEPROM contents (hex):
0x20: 10 0D 01 01 01 A0 C2 85 50 09 BF 01 00 00 00 00
0x30: A0 00 00 00 02 01 09 01 FF FF FF FF FF FF FF FF
WIC/VIC/HWIC Slot 3:
Serial 2T (12in1)
Hardware revision 1.0 Board revision D0
Serial number 35386517 Part number 800-03181-01
FRU Part Number WIC-2T=
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 02 1B F4 95 50 0C 6D 01 00 00 00 00
0x30: 68 00 00 00 00 09 02 00 FF FF FF FF FF FF FF FF
please help!
05-18-2010 03:41 AM
You need IOS version 12.4(20)T.
Cisco IP Communications Voice/Fax Network Module
http://www.cisco.com/en/US/prod/collateral/modules/ps5365/product_data_sheet0900aecd801c595e.html
Please don't forget to rate useful posts. Thanks.
05-19-2010 10:36 PM
Hi,
I have managed to arrange the IOS "c2801-ipvoicek9-mz.124-20.T5.bin", but still the same problem.
please help!
05-19-2010 11:25 PM
experts! i would appreciate the quick response
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide