05-18-2010 03:36 AM - edited 03-15-2019 10:48 PM
Hello,
I am having Cisco 2801 router with IOS "c2801-ipvoicek9-mz.124-20.T5.bin", i have installed VIC2-FXO on slot 2 [ this slot accepts only WICs and VICs] and VIC2-2FXS on slot0 [This slot only accepts VICs]
but the problem is that they both are not showing in show run and show voice port summmary command.
i issued command show diag and found the below out for both slot:
VIC Slot 0:
FXS Voice daughter card (2 port)
WIC module not supported/disabled in this slot
Hardware revision 1.1 Board revision B0
Serial number 27276672 Part number 800-02493-04
FRU Part Number VIC-2FXS=
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0E 01 01 01 A0 35 80 50 09 BD 04 00 00 00 00
0x30: 58 00 00 00 01 12 27 01 FF FF FF FF FF FF FF FF
WIC/VIC/HWIC Slot 1:
4 Port FE Switch
Base MAC Address : 001a.6d50.cbfc
MAC Address block size : 4
PCB Serial Number : FOC10484E9S
Hardware Revision : 6.0
Part Number : 73-8474-06
Board Revision : A0
Top Assy. Part Number : 800-24193-02
Deviation Number : 0
Fab Version : 05
CLEI Code : IPUIA00RAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-4ESW
Version Identifier : V01
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF CF 06 00 1A 6D 50 CB FC 43 00 04 C1 8B 46
0x10: 4F 43 31 30 34 38 34 45 39 53 40 00 56 41 06 00
0x20: 82 49 21 1A 06 42 41 30 C0 46 03 20 00 5E 81 02
0x30: 88 00 00 00 00 02 05 C6 8A 49 50 55 49 41 30 30
0x40: 52 41 41 03 00 81 00 00 00 00 04 00 CB 89 48 57
0x50: 49 43 2D 34 45 53 57 89 56 30 31 20 D9 02 C1 40
0x60: 05 01 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC/VIC Slot 2:
FXO Voice daughter card (2 port)
Unknown EEPROM ver 16
EEPROM format version 16
EEPROM contents (hex):
0x20: 10 0D 01 01 01 A0 C2 85 50 09 BF 01 00 00 00 00
0x30: A0 00 00 00 02 01 09 01 FF FF FF FF FF FF FF FF
WIC/VIC/HWIC Slot 3:
Serial 2T (12in1)
Hardware revision 1.0 Board revision D0
Serial number 35386517 Part number 800-03181-01
FRU Part Number WIC-2T=
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 02 1B F4 95 50 0C 6D 01 00 00 00 00
0x30: 68 00 00 00 00 09 02 00 FF FF FF FF FF FF FF FF
please help!
05-18-2010 03:41 AM
You need IOS version 12.4(20)T.
Cisco IP Communications Voice/Fax Network Module
http://www.cisco.com/en/US/prod/collateral/modules/ps5365/product_data_sheet0900aecd801c595e.html
Please don't forget to rate useful posts. Thanks.
05-19-2010 10:36 PM
Hi,
I have managed to arrange the IOS "c2801-ipvoicek9-mz.124-20.T5.bin", but still the same problem.
please help!
05-19-2010 11:25 PM
experts! i would appreciate the quick response
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: