cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1244
Views
0
Helpful
2
Replies

Switch 4507R compatibility

umum00029
Level 1
Level 1

Dear all,

      The following is the original module on the switch 4507R.

        Its version is      boot system flash bootflash:cat4000-is-mz.121-13.EW.bin

CMDOWNLOAD#sh mod

Mod  Ports Card Type                              Model             Serial No.
----+-----+--------------------------------------+-----------------+-----------
1      2  1000BaseX (GBIC) Supervisor(standby)   WS-X4515          JAB071604SU

2      2  1000BaseX (GBIC) Supervisor(active)    WS-X4515          JAB07150552

3     24  10/100/1000BaseTX (RJ45)               WS-X4424-GB-RJ45  JAB070905HP

4     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE07081DLY

5     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE07081G8B

6     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0727102L

7     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0716065N

Due to upgrade the module on the switch 4507r, I replaced the new Gigabit module for original module 4 (100MB based)

However, I got the error message:

                  0:06:44: %C4K_CHASSIS-3-UNKNOWNLINECARD: Unknown module (Field Replaceable Unit minor type 340) in slot 4

and saw the module status as following


Mod  Ports Card Type                              Model             Serial No.
----+-----+--------------------------------------+-----------------+-----------
1      2  1000BaseX (GBIC) Supervisor(active)    WS-X4515          JAB071604SU

2      2  1000BaseX (GBIC) Supervisor(standby)   WS-X4515          JAB07150552

3     24  10/100/1000BaseTX (RJ45)               WS-X4424-GB-RJ45  JAB070905HP

4      0  Unsupported module                     WS-X4548-GB-RJ45  JAE0918B1S9

5     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE07081G8B

6     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0727102L

7     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0716065N


I found many information showing that WS-X4548-GB-RJ45V is supported by 4507R......

Should I upgrade my IOS?

Thank you so much.

2 Accepted Solutions

Accepted Solutions

Jon Marshall
Hall of Fame
Hall of Fame

umum00029 wrote:


I found many information showing that WS-X4548-GB-RJ45V is supported by 4507R......

Should I upgrade my IOS?

Thank you so much.

Yes you need to upgrade your IOS. You need a minimum of 12.1(19)EW to run that module. From the release notes -

WS-X4548-GB-RJ45

48-port 10/100/1000BASE-T Gigabit Ethernet switching module

12.1(19)EW

12.1(19)EW1

Jon

View solution in original post

Ganesh Hariharan
VIP Alumni
VIP Alumni

Dear all,

      The following is the original module on the switch 4507R.

        Its version is      boot system flash bootflash:cat4000-is-mz.121-13.EW.bin

CMDOWNLOAD#sh mod

Mod  Ports Card Type                              Model             Serial No.
----+-----+--------------------------------------+-----------------+-----------
1      2  1000BaseX (GBIC) Supervisor(standby)   WS-X4515          JAB071604SU

2      2  1000BaseX (GBIC) Supervisor(active)    WS-X4515          JAB07150552

3     24  10/100/1000BaseTX (RJ45)               WS-X4424-GB-RJ45  JAB070905HP

4     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE07081DLY

5     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE07081G8B

6     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0727102L

7     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0716065N

Due to upgrade the module on the switch 4507r, I replaced the new Gigabit module for original module 4 (100MB based)

However, I got the error message:

                  0:06:44: %C4K_CHASSIS-3-UNKNOWNLINECARD: Unknown module (Field Replaceable Unit minor type 340) in slot 4

and saw the module status as following


Mod  Ports Card Type                              Model             Serial No.
----+-----+--------------------------------------+-----------------+-----------
1      2  1000BaseX (GBIC) Supervisor(active)    WS-X4515          JAB071604SU

2      2  1000BaseX (GBIC) Supervisor(standby)   WS-X4515          JAB07150552

3     24  10/100/1000BaseTX (RJ45)               WS-X4424-GB-RJ45  JAB070905HP

Hi,

Yes you need to upgrade the ios to support for the module check out the below link for more information about the ios supported.

http://www.ciscosysteme.org/en/US/prod/collateral/modules/ps2710/ps5494/product_data_sheet0900aecd802109ea.html

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

View solution in original post

2 Replies 2

Jon Marshall
Hall of Fame
Hall of Fame

umum00029 wrote:


I found many information showing that WS-X4548-GB-RJ45V is supported by 4507R......

Should I upgrade my IOS?

Thank you so much.

Yes you need to upgrade your IOS. You need a minimum of 12.1(19)EW to run that module. From the release notes -

WS-X4548-GB-RJ45

48-port 10/100/1000BASE-T Gigabit Ethernet switching module

12.1(19)EW

12.1(19)EW1

Jon

Ganesh Hariharan
VIP Alumni
VIP Alumni

Dear all,

      The following is the original module on the switch 4507R.

        Its version is      boot system flash bootflash:cat4000-is-mz.121-13.EW.bin

CMDOWNLOAD#sh mod

Mod  Ports Card Type                              Model             Serial No.
----+-----+--------------------------------------+-----------------+-----------
1      2  1000BaseX (GBIC) Supervisor(standby)   WS-X4515          JAB071604SU

2      2  1000BaseX (GBIC) Supervisor(active)    WS-X4515          JAB07150552

3     24  10/100/1000BaseTX (RJ45)               WS-X4424-GB-RJ45  JAB070905HP

4     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE07081DLY

5     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE07081G8B

6     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0727102L

7     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JAE0716065N

Due to upgrade the module on the switch 4507r, I replaced the new Gigabit module for original module 4 (100MB based)

However, I got the error message:

                  0:06:44: %C4K_CHASSIS-3-UNKNOWNLINECARD: Unknown module (Field Replaceable Unit minor type 340) in slot 4

and saw the module status as following


Mod  Ports Card Type                              Model             Serial No.
----+-----+--------------------------------------+-----------------+-----------
1      2  1000BaseX (GBIC) Supervisor(active)    WS-X4515          JAB071604SU

2      2  1000BaseX (GBIC) Supervisor(standby)   WS-X4515          JAB07150552

3     24  10/100/1000BaseTX (RJ45)               WS-X4424-GB-RJ45  JAB070905HP

Hi,

Yes you need to upgrade the ios to support for the module check out the below link for more information about the ios supported.

http://www.ciscosysteme.org/en/US/prod/collateral/modules/ps2710/ps5494/product_data_sheet0900aecd802109ea.html

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card