05-24-2010 02:28 PM - edited 03-19-2019 12:59 AM
I have:
Router 2851
CME version 7.1
Cisco Unity Express version (7.0.5)
The config:
--------------------
!
telephony-service
max-ephones 5
max-dn 10
ip source-address 10.10.230.1 port 2000
voicemail 3180
max-conferences 8 gain -6
web admin system name admin password lab
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp 7960 Apr 14 2010 21:31:39
!
!
interface Service-Engine1/0
ip unnumbered Vlan230
service-module ip address 10.10.230.2 255.255.255.0
service-module ip default-gateway 10.10.230.1
!
ip route 10.10.230.2 255.255.255.255 Service-Engine1/0
!
ip http server
ip http authentication local
ip http path flash:
---------------------------
From the Cisco Unity Express Initiañization Wizard, it is neccesary to enter the Callmanager Express Login, but an error is receiver:
In the router I can´t see the GUI file
Router#sh flash:
CompactFlash directory:
File Length Name/status
1 46355244 c2800nm-ipvoice_ivs-mz.124-24.T3.bin
2 660 vlan.dat
[46356032 bytes used, 17869244 available, 64225276 total]
62720K bytes of ATA CompactFlash (Read/Write)
I have the same problem. Do you know how fix it?
Regards
Ivan Rivas
Solved! Go to Solution.
05-25-2010 09:47 AM
Hi,
You can download the GUI files from this link according to the version you have:
1. Download appropriate tar file to tftp server. cme-basic-x.x.x.tar ? contains basic CME
system files including GUI, MoH and phoneloads
cme-gui-x.x.x.tar ? contains basic CME GUI files only
2. Logon to privileged EXEC mode of router CLI
3. Enter archive command to extract contents of tar file to router Flash memory:
Router# archive tar /xtract tftp://ip-address/filename flash:
Example 1:
To extract contents of cme-basic-3.0.3.tar from tftp server 192.168.1.1 to flash:
archive tar /xtract tftp://192.168.1.1/cme-basic-3.0.3.tar flash:
Example 2:
To extract contents of cme-gui-3.0.3.tar from tftp server 192.168.1.1 to flash:
archive tar /xtract tftp://192.168.1.1/cme-gui-3.0.3.tar flash:
This will update all the gui files in the location which the gui checks on the flash.
Regards,
Tere
05-24-2010 02:37 PM
Hi Ivan,
You will need to upload the GUI files to the flash memory. Please refer to:
Regards,
Tere.
05-24-2010 02:58 PM
Thanks, What is the procedure for loading ? because in the document http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_tech_note09186a0080aff515.shtm
said: loading the GUI files to the GUI folder in flash
Thanks
05-25-2010 09:47 AM
Hi,
You can download the GUI files from this link according to the version you have:
1. Download appropriate tar file to tftp server. cme-basic-x.x.x.tar ? contains basic CME
system files including GUI, MoH and phoneloads
cme-gui-x.x.x.tar ? contains basic CME GUI files only
2. Logon to privileged EXEC mode of router CLI
3. Enter archive command to extract contents of tar file to router Flash memory:
Router# archive tar /xtract tftp://ip-address/filename flash:
Example 1:
To extract contents of cme-basic-3.0.3.tar from tftp server 192.168.1.1 to flash:
archive tar /xtract tftp://192.168.1.1/cme-basic-3.0.3.tar flash:
Example 2:
To extract contents of cme-gui-3.0.3.tar from tftp server 192.168.1.1 to flash:
archive tar /xtract tftp://192.168.1.1/cme-gui-3.0.3.tar flash:
This will update all the gui files in the location which the gui checks on the flash.
Regards,
Tere
05-25-2010 12:45 PM
Great, Thanks
Now, the autentication is OK, The problem was the GUI files in the Flash,
The problem was fixed
Thanks again.
Ivan
01-29-2019 07:24 PM
Hi, testeven
Where could I donwload the GUI tar file for CME7.1?
Thanks and regards
01-29-2019 08:09 PM
03-12-2019 02:25 AM
Thanks. Kumar. You are right. I am running CME7.1 on a 2811 router.
Finally, I found the GUI files for CME7.1 version, and solve the issue.
Regards
Sand
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: