05-27-2010 02:51 AM - edited 03-15-2019 10:58 PM
Hi all,
I have a CUCM v7.1 and an Aastra Nexspan linked by QSIG.
Calls works fine between the 2 systems, but I can't display the calling name in the two sides.
The gateway is a cisco 2821 router, configured as a H323 gateway.
Here's the confiruguration of the gw:
!
voice service voip
qsig decode
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
supplementary-service h450.12
h323
!
!
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn protocol-emulate network
isdn incoming-voice voice
isdn supp-service name calling profile Network-Extension operation-value-tag local
isdn send-alerting
isdn negotiate-bchan
isdn sending-complete
isdn outgoing ie facility
isdn outgoing ie extended-facility
isdn outgoing display-ie
isdn outgoing ie connected-number
isdn outgoing ie caller-number
isdn outgoing ie caller-subaddr
isdn outgoing ie called-number
no cdp enable
!
here debug Q931 from 13163 (aastra phone) to 14504 (Cisco Phone): Display calling name : "unknown, external call":
*May 27 09:48:09.296: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0018
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18385
Preferred, Channel 5
Facility i = 0x91AA068001008201008B0100A10B02010006042B0C09008400
Progress Ind i = 0x8083 - Origination address is non-ISDN
Called Party Number i = 0x80, '14504'
Plan:Unknown, Type:Unknown
Sending Complete
*May 27 09:48:09.300: ISDN Se0/2/0:15 **ERROR**: isdn_init_fac_data: No Opval 0
*May 27 09:48:09.304: ISDN Se0/2/0:15 **ERROR**: isdn_init_fac_data: No Opval 0
*May 27 09:48:09.320: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x8018
Channel ID i = 0xA98385
Exclusive, Channel 5
*May 27 09:48:09.460: ISDN Se0/2/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x8018
Facility i = 0x9FAA068001018201018B0100A10902020EF10201018000
*May 27 09:48:10.944: ISDN BR0/0/1 Q931: RX <- CALL_PROC pd = 8 callref = 0xF4
Channel ID i = 0x89
Exclusive, B1
here debug Q931 from 14504 (Cisco Phone) to: 13163 (aastra phone) Display calling name : "14504":
*May 27 09:48:14.608: ISDN Se0/2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0581
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18382
Preferred, Channel 2
Facility i = 0x9FAA068001018201018B0100A10902020EF20201008000
Calling Party Number i = 0x0081, '14504'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '13163'
Plan:Unknown, Type:Unknown
*May 27 09:48:14.656: ISDN Se0/2/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8581
Channel ID i = 0xA18382
Preferred, Channel 2
*May 27 09:48:14.712: ISDN Se0/2/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x8581
Facility i = 0x91AA068001008201008B0100A10B02010006042B0C09018400
Progress Ind i = 0x8081 - Call not end-to-end ISDN, may have in-band info
*May 27 09:48:15.712: ISDN Se0/2/0:15 Q931: RX <- CONNECT pd = 8 callref = 0x8581
Facility i = 0x91AA068001008201008B0100A10B02010006042B0C09028400
Progress Ind i = 0x8081 - Call not end-to-end ISDN, may have in-band info
Connected Number i = 0x80, '13163'
Thanks for your help!
05-27-2010 09:42 AM
Try adding this:
voice service voip
h323
h225 display-ie ccm-compatible
I had to do that to get my inbound cnam to work.
Hope this helps
Rick
05-28-2010 01:09 AM
Hi Rick,
thanks for your help, but I can't enter this command:
voice service voip
h323
h225 display-ie ccm-compatible
it's an Unrecognized command. Here are the available option after h225:
(conf-serv-h323)#h225 ?
alt-ep Alternate endpoint configuration
connect-passthru Connect Pass through
h245-address global control for h225 reporting of h245-address GW
id-passthru Protocol identifier pass through
listen-port Call Signaling Port (default 1720)
signal Specify signaling options
start-h245 global control of initiation of H.245
timeout Specify timeout for maintaining connections
Can you help me again?
the System image file is "flash:c2800nm-spservicesk9-mz.124-15.T12.bin"
05-28-2010 02:19 AM
Sorry for the last post,I upgrade the IOS version in Version 12.4(11)XW10, I can add the command but it still doesn't work...
06-01-2010 05:12 AM
I change the gateway protocol into MGCP, but the problem is the same... Is someone have an idea?
06-10-2010 03:52 AM
Ok today the name is display when a Cisco Phone call an Aastra Phone, but not in the other direction...
here's an extract of the gw config:
!
voice service voip
qsig decode
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
supplementary-service h450.12
h323
h225 timeout ntf 300
h225 display-ie ccm-compatible
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729br8
!
voice class codec 2
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729br8
!
!
!
voice class h323 1
h225 timeout tcp establish 5
h225 timeout ntf 300
h225 display-ie ccm-compatible
!
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn overlap-receiving
isdn protocol-emulate network
isdn incoming-voice voice
isdn map address *. plan isdn type unknown
isdn supp-service name calling ie 40 cs 0 profile Network-Extensions operation-value-tag local
isdn sending-complete
isdn outgoing ie facility
isdn outgoing display-ie
isdn outgoing ie caller-number
no cdp enable
08-31-2012 07:11 AM
Did you find resolution to this problem? I have the exact same setup with the exact same issue.
09-02-2012 11:56 PM
Hi Vladimir,
I had to use the external directory of Aastra Nexpan to display the name on Aastra phone. I was not able to use the name from the qsig frames...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide