3750 with integrated wireless controller , port-channel want came up

Unanswered Question
Jun 1st, 2010
User Badges:

We had WS-C3750G-24WS-S25 running for a long time already (about 6 month).

After power failure switch was came up as long as a wireless controller (I can successfully access both of them via console) , however Port-Channel still in down state.


Is there any CLI commands you can advise I can run on controller to check port/portchannel configuration from controller side ?


I attached various show commands, and any of your advices will be greatly appreciated.


GigabitEthernet1/0/27  unassigned      YES unset  down                  down
GigabitEthernet1/0/28  unassigned      YES unset  down                  down
Port-channel40         unassigned      YES unset  down                  down

0



SWCM_api.c 1976: In call to 'SWCM_register_access()', error: bad args


Jun 01 13:50:19.640 dtl_net.c:602 DTL-3-ARP_SEND_FAILED: Could not send ARP requ
est to 00:1b:53:63:db:07. VLAN=200, Intf=29. pdu transmit error.
- Traceback:  1029f970 103f32dc 10291718 103d409c 10b955a8 10d4ec6c
Jun 01 13:50:19.640 dtl_pdu_landd.c:452 DTL-3-PKT_TX_ERROR: Failed to transmit a
packet of type 0,USP:0/3/1.
- Traceback:  102a50c8 1029f8fc 103f32dc 10291718 103d409c 10b955a8 10d4ec6c
Jun 01 13:50:19.640 sysapi.c:160 SYSTEM-3-SYSAPI_ERR: System Error : dapi.c 1466
: In dapiCtlLagIntf() Frame sent to Lag that does not exist
Jun 01 13:50:19.640 sim.c:784 SIM-3-ARP_SND_FAIL: Unable to send ARP Request. Lo
cal MAC: 00:1B:53:63:DB:00.Ip Addr: 10.0.200.3Interface # 29. Vlan Id: 200
Jun 01 13:50:19.640 dtl_net.c:602 DTL-3-ARP_SEND_FAILED: Could not send ARP requ
est to 00:1b:53:63:db:00. VLAN=200, Intf=29. pdu transmit error.
- Traceback:  1029f970 103f2d74 102916dc 103d409c 10b955a8 10d4ec6c
Jun 01 13:50:19.640 dtl_pdu_landd.c:452 DTL-3-PKT_TX_ERROR: Failed to transmit a
packet of type 0,USP:0/3/1.
- Traceback:  102a50c8 1029f8fc 103f2d74 102916dc 103d409c 10b955a8 10d4ec6c
Jun 01 13:50:19.639 sysapi.c:160 SYSTEM-3-SYSAPI_ERR: System Error : dapi.c 1466
: In dapiCtlLagIntf() Frame sent to Lag that does not exist
Jun 01 13:50:18.790 sntp_main.c:274 SNTP-3-FATAL_ERROR_OCCURED: Fatal error: : u
nable to send NTP packet.
Jun 01 13:50:16.790 sntp_main.c:274 SNTP-3-FATAL_ERROR_OCCURED: Fatal error: : u
nable to send NTP packet.



Burned-in MAC Address............................ 00:1B:53:63:DB:00
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
NAME: "Chassis"    , DESCR: "Cisco Wireless Controller"
PID: WS-C3750G-24WS-S25,  VID: V01,  SN: FOC1117G01F



Load for five secs: 6%/1%; one minute: 6%; five minutes: 6%
Time source is NTP, 09:51:14.861 EST Tue Jun 1 2010


Wireless Controller in Switch 1
Operational Status of the Controller : wait_for_init
Service VLAN                         : 4095
Service Port Mac Address             : ffff.ffff.ffff
Service IP Address                   : 127.0.1.1
Management IP Address                : 0.0.0.0
Management VLAN                      : 0
Software Version                     : unknown
Keepalive Version(controller/switch) : 0/1
Keepalives Missed                    : 0
Controller accepts http/https        : 0/0
Controller's Status Line             : up
Watchdog resets of Controller        : 0
Controller resets total              : 1
Unacknowledged control messages      : 1

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
dancampb Tue, 06/01/2010 - 07:46
User Badges:
  • Cisco Employee,

"'SWCM_register_access()',  error: bad args" often is related to a hardware issue.  Are you able to session into the controller?  If so are the ports showing up?

Andriy Yerofyeyev Tue, 06/01/2010 - 07:59
User Badges:

Thanks for reply,


Yes , I am able to session to controller.


(Cisco Controller) >show port summary

           STP   Admin   Physical   Physical   Link   Link    Mcast
Pr  Type   Stat   Mode     Mode      Status   Status  Trap   Appliance   POE
-- ------- ---- ------- ---------- ---------- ------ ------- --------- -------
807398816 Normal  Disa Enable  10 Full    10 Full    Down   Enable  Enable     N
/A

Actions

This Discussion

Related Content