Cannot find port

Answered Question
Jun 16th, 2010

I have a switch running CatOS 7.6(7). It is being monitored via CA's eHealth. EHealth discovered the element: "POOL-enet-port-179", which is reporting bandwidth out utilization, but I cannot see that configured anywhere on the switch. Can anyone please explain what this is? Show ver is below:

sw-25cr1> (enable) sho ver
WS-C6509 Software, Version NmpSW: 7.6(7)
Copyright (c) 1995-2004 by Cisco Systems
NMP S/W compiled on May  6 2004, 23:37:26

System Bootstrap Version: 5.3(1)
System Boot Image File is 'bootflash:cat6000-supk8.7-6-7.bin'
System Configuration register is 0x2

Hardware Version: 2.0  Model: WS-C6509  Serial #: SCA044701LX

PS1  Module: WS-CAC-1300W    Serial #: SON04422265
PS2  Module: WS-CAC-1300W    Serial #: SON04513645

Mod Port Model               Serial #    Versions
--- ---- ------------------- ----------- --------------------------------------
1   2    WS-X6K-SUP1A-2GE    SAD05030GNH Hw : 7.0
                                         Fw : 5.3(1)
                                         Fw1: 5.4(2)
                                         Sw : 7.6(7)
                                         Sw1: 7.6(7)
         WS-F6K-PFC          SAD05030AJN Hw : 1.1  
                                         Sw :
         WS-X6K-SUP1A-2GE    SAD05030GNH Hw : 7.0  
                                         Sw :
3   16   WS-X6416-GE-MT      SAD04190GE3 Hw : 1.1
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
4   48   WS-X6248A-TEL       SAD04450DBM Hw : 2.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
5   48   WS-X6248A-TEL       SAD04290CJT Hw : 3.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
6   48   WS-X6248A-TEL       SAL05062ZK1 Hw : 2.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
7   48   WS-X6248A-TEL       SAD041906BH Hw : 3.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
8   48   WS-X6148-GE-TX      SAD075304E8 Hw : 6.0
                                         Fw : 7.2(1)
                                         Sw : 7.6(7)
9   48   WS-X6148-GE-TX      SAL094760WW Hw : 7.0
                                         Fw : 7.2(1)
                                         Sw : 7.6(7)
15  1    WS-F6K-MSFC2        SAD05030N19 Hw : 1.2
                                         Fw : 12.1(11b)E1
                                         Sw : 12.1(11b)E1

       DRAM                    FLASH                   NVRAM
Module Total   Used    Free    Total   Used    Free    Total Used  Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1       65408K  48172K  17236K  16384K  10924K   5460K  512K  444K   68K

Uptime is 402 days, 3 hours, 16 minutes

I have this problem too.
0 votes
Correct Answer by jorge.calvo about 6 years 5 months ago

Hello,

That port number usually refers to the MIB ifIndex assigned to a certain port. You can try to find port the associated to the PHY 179 with the next command:

show port ifindex

Hope this helps.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
jorge.calvo Thu, 06/17/2010 - 00:28

Hello,

That port number usually refers to the MIB ifIndex assigned to a certain port. You can try to find port the associated to the PHY 179 with the next command:

show port ifindex

Hope this helps.

Actions

This Discussion

Related Content