Sup V-10GE question

Answered Question
Jun 16th, 2010

I have 2 Sup V-10GE in each of my C4507R-E switches. They are in SSO mode. Te3/1 is connected. Te 4/1 is connected. Te3/2 is inactive. Te 4/2 is inactive.

Can I use Te 3/2 and Te 4/2 in channel mode for a Nexxus switch uplink?

I have 2 of these C4507R-E as my core switches and will want to do the same identical setup to the 2nd core switch

I have this problem too.
0 votes
Correct Answer by Viral Bhutta about 6 years 5 months ago

Thats is correct.

Correct Answer by Viral Bhutta about 6 years 5 months ago

Check This out

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/52sg/configuration/guide/RPR.html#wp1097897

When you select 10-Gigabit Ethernet uplinks on WS-X4516-10GE and WS-X4013+10GE Supervisor Engines in RPR or SSO mode, only TenGigabitEthernet 1/1 and 2/1 interfaces are available. Similarly, when you select Gigabit Ethernet uplinks, only GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available. When you select to use both uplinks concurrently, TenGigabitEthernet 1/1 and 2/1 interfaces and GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available.

Hope this helps.

Correct Answer by Viral Bhutta about 6 years 5 months ago

If I am not wrong then

Dual uplinks are supported in the following modes of operation:

1) If there are two sups in the device, you can have the first TenGig of
each sup active and acting as an uplink.

or 

2) If there is a single sup in the chassis, then two interfaces on the same
sup would be active and acting as an uplink.

You cannot have dual uplinks on a single sup active when dual sups are
installed in the system.
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (3 ratings)
Loading.
Correct Answer
Viral Bhutta Sat, 06/19/2010 - 19:46

If I am not wrong then

Dual uplinks are supported in the following modes of operation:

1) If there are two sups in the device, you can have the first TenGig of
each sup active and acting as an uplink.

or 

2) If there is a single sup in the chassis, then two interfaces on the same
sup would be active and acting as an uplink.

You cannot have dual uplinks on a single sup active when dual sups are
installed in the system.
Correct Answer
Viral Bhutta Sat, 06/19/2010 - 19:50

Check This out

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/52sg/configuration/guide/RPR.html#wp1097897

When you select 10-Gigabit Ethernet uplinks on WS-X4516-10GE and WS-X4013+10GE Supervisor Engines in RPR or SSO mode, only TenGigabitEthernet 1/1 and 2/1 interfaces are available. Similarly, when you select Gigabit Ethernet uplinks, only GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available. When you select to use both uplinks concurrently, TenGigabitEthernet 1/1 and 2/1 interfaces and GigabitEthernet 1/3, 1/4, 2/3, and 2/4 interfaces are available.

Hope this helps.

rzulueta315 Mon, 06/21/2010 - 14:35

Thanks for the replies. Since I do have it in SSO mode I can only use Te 3/1 and Te 4/1.

Actions

This Discussion