IPV6 and failover 8.0.4

Unanswered Question
Jun 23rd, 2010
User Badges:

Hi,


we are getting the following messages in our PIX with 8.0.4 SW version:


/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} %PIX-6-110002: Failed to locate egress interface for UDP int_inside:IPV6add to IPV6add2

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} %PIX-6-110002: Failed to locate egress interface for TCPint_inside:IPV6add to IPV6add2


this only happens when we have the PIXs in failover, if we put it in standalone both work without this problem..


failover it's already supported with IPV6 configured?


Thank you.



/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Marcin Latosiewicz Wed, 06/23/2010 - 10:07
User Badges:
  • Cisco Employee,

Norberto,


IPv6 failover is supported as of ASA (not PIX) version 8.2.2


Do you receive those messages on active unit?


Marcin

Norberto Salgado Wed, 06/23/2010 - 10:13
User Badges:

We have the failover configured in ipv4 but we are using ipv6 also..is failover unsupported in this scenarium? Or it's just unsupported if we have the failover configured with ipv6 addresses?

Marcin Latosiewicz Wed, 06/23/2010 - 10:26
User Badges:
  • Cisco Employee,

Norberto,


Before 8.2.2 both active and standby unit were using same IPv6 address which is already quite interesting for say management purposes


Marcin

Norberto Salgado Wed, 06/23/2010 - 10:32
User Badges:

But in double-stack (with the failover configured with ipv4) it's this supported?

Marcin Latosiewicz Wed, 06/23/2010 - 10:39
User Badges:
  • Cisco Employee,

If you're aware of the limitations I don't think anyone will claim it's not supported.

Actions

This Discussion