06-28-2010 12:17 PM - edited 03-06-2019 11:47 AM
After manual reload appears this message:
*Jun 28 08:05:09.675: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Jun 28 08:05:08.335: CM file (ivfs:/s72033_sp-advipservicesk9-m_matrix.cm) is not readable, using internal matrix table
*Jun 28 08:05:08.799: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
*Jun 28 08:05:08.839: %C6K_PLATFORM-4-DETECTED_NON_C7600_CHASSIS: Software has detected an attempt to run a c7600 image on an incompatible chassis WS-C6509 (36866)
*Jun 28 08:05:09.671: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
And the modules 1 and 8 turn down.
Can someone say me what is the possible cause?
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAD0805022X
3 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE JAF1212BRPG
4 8 8 port 1000mb ethernet WS-X6408-GBIC SAD041500KU
5 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAD0951035V
6 2 Supervisor Engine 720 (Hot) WS-SUP720-3BXL SAD1208029X
7 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL0506310M
8 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAD091503B5
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 000e.83ea.c0d4 to 000e.83ea.c103 1.4 12.2(14r)S5 12.2(33)SRD Ok
3 001f.6cad.8490 to 001f.6cad.8493 2.7 12.2(14r)S5 12.2(33)SRD Ok
4 00d0.d3a0.d89c to 00d0.d3a0.d8a3 2.4 5.1(1)CSX 8.7(0.22)FW2 Ok
5 0011.5cab.80bc to 0011.5cab.80bf 4.3 8.1(3) 12.2(33)SRD Ok
6 0013.807b.9ed0 to 0013.807b.9ed3 5.6 8.5(2) 12.2(33)SRD Ok
7 0001.9724.0c14 to 0001.9724.0c1b 1.3 5.4(2) 8.7(0.22)FW2 Ok
8 0012.0059.a4a4 to 0012.0059.a4bb 2.2 12.2(14r)S5 12.2(33)SRD Ok
------------------ show version ------------------
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRD, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 24-Oct-08 02:34 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
R6500 uptime is 9 weeks, 6 days, 19 hours, 43 minutes
Uptime for this control processor is 9 weeks, 6 days, 19 hours, 38 minutes
System returned to ROM by power cycle (SP by power on)
System restarted at 10:25:45 BSAS Wed Apr 14 2010
System image file is "disk0:s72033-advipservicesk9-mz.122-33.SRD.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C6509 (R7000) processor (revision 2.0) with 983008K/65536K bytes of memory.
Processor board ID SCA050702WY
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from power-on
27 Virtual Ethernet interfaces
92 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
06-28-2010 12:44 PM
As the following message describe
*Jun 28 08:05:08.839: %C6K_PLATFORM-4-DETECTED_NON_C7600_CHASSIS: Software has detected an attempt to run a c7600 image on an incompatible chassis WS-C6509 (36866)
You are using the C7600 software (SRx train) on a C6500 hardware. This is not a support solution, and you should use the C6500 software instead (SXx).
Regards,
jerry
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide