06-30-2010 12:41 AM
Hello experts,
I have a problem about the WAAS optimization.
The topology is...
Center: 7200 Router working with WCCP (512 WAE)
Edge: 2800 Router working with WCCP (612 WAE)
When i tried to reach the Database (behind the 7200 Router) from the Edge site. its working! but during this time, when i look the Current Connection status, there is no optimization traffic(you can see the attach file).
I have done this setup, demo etc. too many times, but the first time i encountered such a problem.
you can see the configuration at the below.
By the way, when i look the "show ip wccp" command output. there is no traffic on Service identifier 62. Do we need to see increased this traffic?
Thanks in advance for your help.
BM-7206-METRO#show ip wccp
Global WCCP information:
Router information:
Router Identifier: 10.200.200.193
Protocol Version: 2.0
Service Identifier: 61
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Total Packets s/w Redirected: 37207
Process: 0
Fast: 0
CEF: 37207
Service mode: Open
Service access-list: -none-
Total Packets Dropped Closed: 0
Redirect access-list: 199
Total Packets Denied Redirect: 1074214
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
Service Identifier: 62
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Total Packets s/w Redirected: 0
Process: 0
Fast: 0
CEF: 0
Service mode: Open
Service access-list: -none-
Total Packets Dropped Closed: 0
Redirect access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
**************************************************
**************************************************
CORE_WAE
configure terminal
primary-interface gigabitEthernet 1/0
device mode application-accelerator
central-manager address 10.10.10.10
cms enable
wccp version 2
wccp router-list 1 2.2.2.1 (ROUTER IP add)
wccp tcp-promiscuous router-list-num 1
**************************************************
**************************************************
EDGE_WAE
configure terminal
primary-interface gigabitEthernet 1/0
device mode application-accelerator
central-manager address 10.10.10.10
cms enable
wccp version 2
wccp router-list 1 1.1.1.1
wccp tcp-promiscuous router-list-num 1
**************************************************
**************************************************
CORE_ROUTER
ip wccp version 2
ip wccp 61
ip wccp 62
interface gi 2/0 (LAN)
ip wccp 61 redirect in
interface gi 3/0.26 (WAN) (Note: also this interface have a Tunnel int. connect to edge router tunnel int.)
ip wccp 62 redirect in
interface gi 1/0 (WAE LAN)
ip wccp redirect exclude in
ip cef
**************************************************
**************************************************
EDGE_ROUTER
ip wccp version 2
ip wccp 61
ip wccp 62
interface gi 1/0 (LAN)
ip wccp 61 redirect in
interface ATM 2/0.1 (WAN) (Note: also this interface have a Tunnel int. connect to central router tunnel int.)
ip wccp 62 redirect in
interface gi 2/0 (WAE LAN)
ip wccp redirect exclude in
ip cef
**************************************************
**************************************************
07-01-2010 04:44 AM
Is the traffic going over the GRE tunnel between these sites? Based on the output you provided, I suspect you need to apply ip wccp redirect 62 in on the tunnel interface itself.
Regards,
Zach
07-01-2010 05:13 AM
Hello Zach,
Yes, the traffic going over the gre tunnel between the sites. When i tried to apply the "ip wccp redirect 62" command under the tunnel interface. I can not reach the edge router (with telnet, ssh or etc.)
I think, the problem occurs from the IPSEC traffic or something securtiy issue or MTU size. I also check the documents(cisco.com) for both situation, but everything seems to be ok.
bythe way
If you need any command output, i can provide. also routers configuration (i can email to you.)
thanks.
07-01-2010 08:20 AM
Can you tell me what IOS version you are running and provide a copy of the your router configuration?
Thanks,
Zach
07-02-2010 04:16 AM
Hi Zach
Center router IOS version is c7200-advipservicesk9_li-mz.124-11.T.bin
Edge router IOS version is c2800nm-adventerprisek9-mz.124-9.T2.bin
Also you can see the configurations at the attach
Thanks,
My best.
CORE WAE CONFIG:
Based on the input, the following configurations will be done:
central-manager address 10.166.0.10
interface GigabitEthernet 1/0
ip address 10.166.0.20 255.255.0.0
autosense
exit
ip default-gateway 10.166.0.1
ip name-server 10.201.0.201
ip domain-name tcmb.gov.tr
primary-interface GigabitEthernet 1/0
hostname CORE
clock timezone UTC 0 0
wccp version 2
wccp router-list 8 10.166.0.1
wccp tcp-promiscuous router-list 8
cms enable
EDGE WAE CONFIG:
Based on the input, the following configurations will be done:
central-manager address 10.166.0.10
interface GigabitEthernet 1/0
ip address 10.126.2.20 255.255.255.0
autosense
exit
ip default-gateway 10.126.2.1
ip name-server 10.201.0.201
ip domain-name tcmb.gov.tr
primary-interface GigabitEthernet 1/0
hostname EDGE
clock timezone UTC 0 0
wccp version 2
wccp router-list 8 10.126.2.1
wccp tcp-promiscuous router-list 8
cms enable
07-05-2010 12:04 AM
Hi Zach,
Is there any update about the problem?
thanks
Cavit
07-06-2010 07:05 AM
It's possible that you are running into IOS defect CSCsg30875. Can you try using an access-list with the WCCP services that excludes traffic destined to the router IP addresses?
Thanks,
Zach
07-07-2010 07:32 AM
Hi Zach,
it's working now,
when i apply the ip wccp command to tunnel interface, with exclude the all telnet and ssh traffic. Optimization working fine, somehow when i have downloaded something from the internet, i cant see the any compression about HTTP traffic. (I choose the FULL optimization for HTTP traffic)
anyway i am working on this problem... thank you very much for your help.
My Best
Cavit Davutoglu.
07-14-2010 05:48 AM
Thanks for the update Cavit.
Please feel free to create a new post if you want to troubleshoot the HTTP acceleration problem.
Regards,
Zach
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide