cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1619
Views
15
Helpful
8
Replies

Cannot use the command "warm-reload" on IOS 12.4T

cisco_fun_4899
Level 1
Level 1

Hi,

I would like to use the command "warm-reload" like the following documentations on the router 2611XM with IOS 12.4T.

http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/warm_reload_ps6441_TSD_Products_Configuration_Guide_Chapter.html

I thought it available, but actually at the consol which connected with the router, it did not exist.

How can I use this command on the IOS 12.4T?

Regards,

Okumura

1 Accepted Solution

Accepted Solutions

Warm-reboot is not supported on the 2600 platform.  This is documented by this bug which is closed.

CSCec31846    Add warm reboot capability to 2600 series

View solution in original post

8 Replies 8

Ganesh Hariharan
VIP Alumni
VIP Alumni

Hi,

I would like to use the command "warm-reload" like the following documentations on the router 2611XM with IOS 12.4T.

http://www.cisco.com/en/US/docs/ios/fundamentals/configuration/guide/warm_reload_ps6441_TSD_Products_Configuration_Guide_Chapter.html

I thought it available, but actually at the consol which connected with the router, it did not exist.

How can I use this command on the IOS 12.4T?

Regards,

Okumura

Okumura,

What it showing when your configuring in global mode  warm-reboot in router console.

Ganesh.H

Hi, Ganesh.H

Thank you for your reply.

My consol shows below.

*************************************************************************

Router#show version
Cisco IOS Software, C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 13-Aug-08 16:09 by prod_rel_team

ROM: ROMMON Emulation Microcode
ROM: C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)

Router uptime is 2 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"

...

...

Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#warm-reboot
                ^
% Invalid input detected at '^' marker.

Router(config)#

*************************************************************************

Regards,

Okumura

Hi, Ganesh.H

Thank you for your reply.

My consol shows below.

*************************************************************************

Router#show version
Cisco IOS Software, C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 13-Aug-08 16:09 by prod_rel_team

ROM: ROMMON Emulation Microcode
ROM: C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)

Router uptime is 2 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"

...

...

Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#warm-reboot
                ^
% Invalid input detected at '^' marker.

Router(config)#

*************************************************************************

Regards,

Okumura

Hi Okumura,

Yes you are right and i have also seen in the command lookup tool it also shows avalibale from 12.4 and T series,But when i am trying to fetch your ios i am unable to find the particular in feature navigator for particular ios to support this feature.

 C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)

Ganesh.H

Hi Ganesh.H

Yes, I am unable to find the particular too.

I can't figure out what's behind it.

So mysterious.

Regards,

Okumura

Warm-reboot is not supported on the 2600 platform.  This is documented by this bug which is closed.

CSCec31846    Add warm reboot capability to 2600 series

Hi Gregory Camp,

Thank you for your reply.

I got it.

And then, What means "CSCec31846".

I can't find "CSCec" in Google.com.

Regards,

Tomoyuki

Hi Gregory

I'm sorry for not replying sooner.

I have no permission enough to access its link.

But my question has resolved because it is official bug.

Thank you.

Regards,

Tomoyuki

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card