07-06-2010 07:31 AM
Hello everyone,
I got a network with Siemens Scalance XR300M switches, and I got to do an optical connection to a Catalyst 3750 (3750G-24TS-1U).
The Siemens has a Gigabit Interface with SC Ports over SMF@1310nm (10 km module).
Which GBIC module should I use to connect both of them?
I looked at cisco.com and I saw only one SFP@1310 GBIC module (GLC-EX-SMD). But it is for longer distances!! (I suppose that a SMF@1300nm module will not be compatible with the SMF@1310nm in the Siemens Switch, right?)
Thanks in advance for your help!
Best regards,
Fabio
Solved! Go to Solution.
07-07-2010 04:06 PM
"bit I just saw that there are 1300nm-1310nm converters for non DWDM links"
Can you post the link what you saw? As i saw only 1300Multimode to 1310 Single mode converter. It is totally different thing.
Like Optical power have range for a transmitter similarly Optical Wavelenght have a range and i am 99.999% sure that 1300/1310 will fall into that. (i didnot get any document and dont have much time to research.). If you have 50 same transmitter from Cisco you will find that all are at different wavelength defined by standard.
For your satisfaction ask your cisco supplier that i have siemens optical module will this work with that one or not.
07-07-2010 06:09 PM
viyuan700 is correct is what he says.
The Cisco GLC-LH-SM transceiver will interface with your Siemen's Gigabit Ethernet 10km SMF interface. The actual IEEE 802.3 spec for Gigabit Ethernet 1000BASE-LX outlines a transmit and receive wavelength range of 1270 to 1355 nm; which covers both 1300 and 1310nm. Look at Section 38.4 - PMD to MDI optical specifications for 1000BASE-LX for the specifications.
The data sheet posted on Cisco's website (link below) indicates the GLC-LH-SM= is 1310nm.
Cisco Gigabit Ethernet SFP Data Sheet
Sometimes vendors used 1300nm as a designation for MMF interface and 1310nm for SMF. Probably a reason but I don't know why.
I hope this helps! Let us know if you have any other questions.
Tom
07-08-2010 07:03 AM
The connector mismatch does not matter. You can easily purchase hybrid optical jumper cables with SC connectors on one end and LC connectors on the other.
Good luck!
07-06-2010 09:08 AM
1000BASE-LX/LH SFP for Both Multimode and Single-Mode Fibers and for SMF for 10Km like the pther you have check this link for comptibility matrix
07-06-2010 10:48 PM
07-06-2010 11:37 PM
Is it a 1300nm module compatible with a 1310nm module???
10nm diference matters when we consider DWDM systems but for these modules it doesnot matter that much. Will work without problem and even these modules follow standards too.
07-06-2010 11:58 PM
Sure? Googling a little bit I just saw that there are 1300nm-1310nm converters for non DWDM links.
07-07-2010 04:06 PM
"bit I just saw that there are 1300nm-1310nm converters for non DWDM links"
Can you post the link what you saw? As i saw only 1300Multimode to 1310 Single mode converter. It is totally different thing.
Like Optical power have range for a transmitter similarly Optical Wavelenght have a range and i am 99.999% sure that 1300/1310 will fall into that. (i didnot get any document and dont have much time to research.). If you have 50 same transmitter from Cisco you will find that all are at different wavelength defined by standard.
For your satisfaction ask your cisco supplier that i have siemens optical module will this work with that one or not.
07-07-2010 06:09 PM
viyuan700 is correct is what he says.
The Cisco GLC-LH-SM transceiver will interface with your Siemen's Gigabit Ethernet 10km SMF interface. The actual IEEE 802.3 spec for Gigabit Ethernet 1000BASE-LX outlines a transmit and receive wavelength range of 1270 to 1355 nm; which covers both 1300 and 1310nm. Look at Section 38.4 - PMD to MDI optical specifications for 1000BASE-LX for the specifications.
The data sheet posted on Cisco's website (link below) indicates the GLC-LH-SM= is 1310nm.
Cisco Gigabit Ethernet SFP Data Sheet
Sometimes vendors used 1300nm as a designation for MMF interface and 1310nm for SMF. Probably a reason but I don't know why.
I hope this helps! Let us know if you have any other questions.
Tom
07-07-2010 11:03 PM
Thanks!!
Anyway, the different connector types won't be a problem, right?
07-08-2010 07:03 AM
The connector mismatch does not matter. You can easily purchase hybrid optical jumper cables with SC connectors on one end and LC connectors on the other.
Good luck!
07-07-2010 11:01 PM
Thanks! :-) :-)
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: