Telnet to direct 5 10 vty line from R1 to R2?

Answered Question
Jul 8th, 2010

We have two router R1 and R2 and R2 have on configure 3 different line but default is 0 3 now I want to direct access on line 5 10 as show in picture, so please suggest me how I can telnet to direct on line 10 to 15 or any other line from R1 to R2 but not on default.

Attachment: 
I have this problem too.
0 votes
Correct Answer by Ganesh Hariharan about 6 years 4 months ago

Hi Dear Friends,

I got the answer from cisco doc. we have configure the Rotory command on line with specific no. like below.

!
!
line con 0
transport input none
line aux 0
line vty 0 3
password cisco
login
rotary 2
line vty 4
password network
login
rotary 3
line vty 5 10
password abhinay
login
rotary 1
!
end

R2#
R2#

Thanks for providing a new thing,learned a new thing today !!

Ganesh.H

Correct Answer by wang baojun about 6 years 4 months ago

Good , nice application.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (4 ratings)
Loading.
Ganesh Hariharan Thu, 07/08/2010 - 05:44
We have two router R1 and R2 and R2 have on configure 3 different line
but default is 0 3 now I want to direct access on line 5 10 as show in
picture, so please suggest me how I can telnet to direct on line 10 to
15 or any other line from R1 to R2 but not on default.

Hi,

If you want to use specifc vty session, you can use if you have configured password under vty like in your case you have already configured password at different vty lines

vty 0 3
password cisco
login
vty 4
password network
login
vty 5 10
password abhinay
login

so if you type the password abhinay you will land up in vty session 5 and if another user try and type the same password he will landup in vty session 6 like that.

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

abhi-adte Thu, 07/08/2010 - 06:14

     No yar its not done u check one i did same process....   

abhi-adte Thu, 07/08/2010 - 20:55

Hi Dear Friends,

I got the answer from cisco doc. we have configure the Rotory command on line with specific no. like below.

!
!
line con 0
transport input none
line aux 0
line vty 0 3
password cisco
login
rotary 2
line vty 4
password network
login
rotary 3
line vty 5 10
password abhinay
login
rotary 1
!
end

R2#
R2#

after that come on R1 and #telnet 10.0.0.2

so my orignal command from R1 to R2 telnet is :

R1#telnet 10.0.0.1 3003

Passwod: network

Correct Answer
Ganesh Hariharan Thu, 07/08/2010 - 22:13

Hi Dear Friends,

I got the answer from cisco doc. we have configure the Rotory command on line with specific no. like below.

!
!
line con 0
transport input none
line aux 0
line vty 0 3
password cisco
login
rotary 2
line vty 4
password network
login
rotary 3
line vty 5 10
password abhinay
login
rotary 1
!
end

R2#
R2#

Thanks for providing a new thing,learned a new thing today !!

Ganesh.H

Actions

This Discussion