Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
39028
Views
1
Helpful
6
Replies

IP IGMP SNOOPING QUERIER ON A PER VLAN

inshu.inshu
Level 1
Level 1

‎07-13-2010 02:24 AM - edited ‎03-17-2019 10:03 PM

Hi,

I am using a 4507R cisco switch and I need to enable IP IGMP SNOOPING VLAN 4 QUERIER, which is for my IPTV vlan.

I did try to enable this and get below error. I have an IP address assigned for the vlan 4.

"" Core_AlGosaibi(config)#int vlan 4
Core(config-if)#ip igmp snooping querier
IGMP Querier function cannot be operationally enabled on some VLANs because the required conditions have not been met.""

I see the IGMP version to be 3, will it make any difference?

few are some outputs for your reference, but it doesnt show igmp snooping querier (enabled/disabled) kindly help.

Corei#sh ip igmp snooping vlan 4
Global IGMP Snooping configuration:
-----------------------------------
IGMP snooping              : Enabled
IGMPv3 snooping            : Enabled
Report suppression         : Enabled
TCN solicit query          : Disabled
TCN flood query count      : 2
Last Member Query Interval : 1000

Vlan 4:
--------
IGMP snooping                       : Enabled
IGMPv2 immediate leave              : Disabled
Explicit host tracking              : Enabled
Multicast router learning mode      : pim-dvmrp
Last Member Query Interval          : 1000
CGMP interoperability mode          : IGMP_ONLY

When I globally enabled ip igmp snooping querier and then enter the command " ip igmp snooping vlan 4 querier " it takes.

But again this command is globally enabled, will it make any issues during query with respect to the query IP address??

Please help.

Thanks,

MI

Labels:
0 Helpful
6 Replies 6

inshu.inshu
Level 1
Level 1

‎07-13-2010 02:30 AM

Now I see that the the IGMP snooping querier is enabled for all the vlans since I entered it globally, is there anyway in which I can get it enabled for only IPTV vlan which is my Vlan 4? Please advise.

Also operational state is showing non querier, is it because some problems with configurations?

Core#sh ip igmp snooping querier vlan 4 detail

Global IGMP switch querier status
--------------------------------------------------------
admin state                    : Enabled
admin version                  : 2
source IP address              : 0.0.0.0
query-interval (sec)           : 60
max-response-time (sec)        : 10
querier-timeout (sec)          : 120
tcn query count                : 2
tcn query interval (sec)       : 10

Vlan 4:   IGMP switch querier status
--------------------------------------------------------
admin state                    : Enabled
admin version                  : 2
source IP address              : 10.20.4.1
query-interval (sec)           : 60
max-response-time (sec)        : 10
querier-timeout (sec)          : 120
tcn query count                : 2
tcn query interval (sec)       : 10
operational state              : Non-Querier
operational version            : 2
tcn query pending count        : 0
Corei#sh ip igmp snooping querier vlan 8 detail

Global IGMP switch querier status
--------------------------------------------------------
admin state                    : Enabled
admin version                  : 2
source IP address              : 0.0.0.0
query-interval (sec)           : 60
max-response-time (sec)        : 10
querier-timeout (sec)          : 120
tcn query count                : 2
tcn query interval (sec)       : 10

Vlan 8:   IGMP switch querier status
--------------------------------------------------------
admin state                    : Enabled
admin version                  : 2
source IP address              : 10.20.8.1
query-interval (sec)           : 60
max-response-time (sec)        : 10
querier-timeout (sec)          : 120
tcn query count                : 2
tcn query interval (sec)       : 10
operational state              : Non-Querier
operational version            : 2
tcn query pending count        : 0

Thanks,

MI

0 Helpful

idrisoye123
Level 1
Level 1
In response to inshu.inshu

‎03-31-2012 04:45 AM

Dear inshu.inshu,

How did you eventually solve this issue? Please I need your help on similar issue.

I have a VLAN for IPTV for which i like configure multicast to be restricted only to the IPTV VLAN.

Thanks

idrisoye@yahoo.com

0 Helpful

inshu.inshu
Level 1
Level 1
In response to idrisoye123

‎04-25-2012 06:14 AM

Hi Idris,

Enable igmp querier on core switch and immediate leave on the access switch particular vlan.

Thanks

idrisoye123
Level 1
Level 1
In response to inshu.inshu

‎05-02-2012 06:26 AM

Inshu,

Many thanks. But I did not understand what you meant in the bold text:

Enable igmp querier on core switch and immediate leave on the access switch particular vlan. 

Please explain.

 

“We should all have the right to free speech and expression of opinions. Wisdom is knowing when, where, and how to use them”

0 Helpful

Surya ARBY
Level 4
Level 4

‎09-30-2012 01:08 PM

Bump !

Issue still there in the last firmware on sup7; has someone opened a case about this ?

http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/15.1/XE_330SG/configuration/guide/multi.html#wp1163784

The doc is clear :

The IGMP Snooping Querier feature can be enabled either globally or per-VLAN.

but it's wrong ! I'm running

D7402_DC#show version 
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.03.01.SG RELEASE SOFTWARE (fc2)Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sun 26-Aug-12 13:45 by prod_rel_team
[...]

System image file is "bootflash:/cat4500e-universalk9.SPA.03.03.01.SG.151-1.SG1.bin"

By default IGMP snooping is Enabled and IGMP snooping querier is disabled :

D7402_DC(config)#ip igmp snooping vlan 4 querier 
Command did not take effect due to reason: IGMP switch querier is globally disabled.

So of course I enable it globally; and IGMP snooping querier is applied on all VLANs

D7402_DC(config)#ip igmp snooping querier 

D7402_DC#show ip igmp snooping querier 
Vlan      IP Address               IGMP Version   Port             
-------------------------------------------------------------
1         172.22.248.42            v2            Switch                   
4         10.160.0.5               v2            Switch                   
8         172.22.248.42            v2            Switch                   
9         172.22.248.42            v2            Switch                   
10        172.22.248.42            v2            Switch                 
11        172.22.248.42            v2            Switch                   
12        172.22.248.42            v2            Switch

But when I issue 

D7402_DC(config)#no ip igmp snooping querier 

the command is deleted from the config but IGMP snooping querier is still active on ALL Vlans; of you want to disable IGMP snoopin querier; you have to disable IGMP snooping and then enable it again if you want to keep L2 multicast forwarding logic 

D7402_DC(config)#no ip igmp snooping querier 
D7402_DC(config)#exit
D7402_DC#show ip igmp snooping querier 
Vlan      IP Address               IGMP Version   Port             
-------------------------------------------------------------
1         172.22.248.42            v2            Router                   
4         10.160.0.5               v2            Router                   
8         172.22.248.42            v2            Router                   
9         172.22.248.42            v2            Router                   
10        172.22.248.42            v2            Router                   
11        172.22.248.42            v2            Router                   
12        172.22.248.42            v2            Router                   
D7402_DC#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
D7402_DC(config)#no ip igmp snooping 
D7402_DC(config)#exit
D7402_DC#show ip igmp snooping querier 
Vlan      IP Address               IGMP Version   Port             
-------------------------------------------------------------
D7402_DC#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
D7402_DC(config)#ip igmp snooping 
D7402_DC(config)#
D7402_DC(config)#
D7402_DC(config)#exit
D7402_DC#conf tshow ip igmp snooping querier 
Vlan      IP Address               IGMP Version   Port             
-------------------------------------------------------------
D7402_DC#
0 Helpful

Ferzan Unlu
Level 1
Level 1

‎03-27-2019 12:23 AM

You also need to specify igmp switch querier source address globally.

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents