Configure FXO Ports for Cell Phone Traffic

Answered Question
Jul 14th, 2010
User Badges:

Hi,


I am new enough to Cisco Ip telephony but managed to get a second FXO card configured on my Solution this morning (CME)

I have some mobile pro-links and would like to have the Call Manager take all calls with a cell phone prefix and send them to specific ports on my FXO card.


Does anybody know how this can be done?



Best Regards,

Paul.

Correct Answer by Brandon Buffin about 6 years 11 months ago

You would need to configure dial peers that match the prefix such as:


dial-peer voice 1 pots

destination-pattern 9123456....

forward-digits 10

port 0/0/0


Probably going to need several dial peers to accomplish this.


Hope this helps.


Brandon

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
Brandon Buffin Wed, 07/14/2010 - 06:45
User Badges:
  • Purple, 4500 points or more

You would need to configure dial peers that match the prefix such as:


dial-peer voice 1 pots

destination-pattern 9123456....

forward-digits 10

port 0/0/0


Probably going to need several dial peers to accomplish this.


Hope this helps.


Brandon

pwynne2009 Wed, 07/14/2010 - 07:53
User Badges:

Hey Brandon,


Thanks a million for this. I had to tweak it slowly as I am using dial peers in Ireland.

I need to plug in the mobile links now and test.


thanks again,


Paul.

pwynne2009 Thu, 07/15/2010 - 03:27
User Badges:

Hey Brandon,


I have the card up runnign and its handling calls as part of my hunting group though I am trying to configure two physical POTS ports on the FXo card to route all cell phone traffic when available. Below is the config I have added for the card and for the call treatment.


voice-port 0/2/0
trunk-group FXO_GROUP 5
connection plar 6001
caller-id enable
!
voice-port 0/2/1
trunk-group FXO_GROUP 6
connection plar 6001
caller-id enable
!
voice-port 0/2/2
trunk-group FXO_GROUP 7
connection plar 6001
caller-id enable
!
voice-port 0/2/3
trunk-group FXO_GROUP 8
connection plar 7099
caller-id enable
!
!
dial-peer voice 2000 pots
trunkgroup FXO_GROUP 9
destination-pattern 9T
!
dial-peer voice 2001 pots
trunkgroup FXO_GROUP 10
destination-pattern 999
prefix 999

Dial peer to direct cell Phone calls to the Prolinks.

dial-peer voice 3000 pots
destination-pattern 9086........
forward-digits all
port 0/2/2

dial-peer voice 3001 pots
destination-pattern 9087........
forward-digits all
port 0/2/2

dial-peer voice 3001 pots
destination-pattern 9085........
forward-digits all
port 0/2/2

dial-peer voice 3001 pots
destination-pattern 9083........
forward-digits all
port 0/2/2


dial-peer voice 3000 pots
destination-pattern 9086........
forward-digits all
port 0/2/3

dial-peer voice 3001 pots
destination-pattern 9087........
forward-digits all
port 0/2/3

dial-peer voice 3001 pots
destination-pattern 9085........
forward-digits all
port 0/2/3

dial-peer voice 3001 pots
destination-pattern 9083........
forward-digits all
port 0/2/3



Any ideas on this?


paul.

pwynne2009 Thu, 07/15/2010 - 04:47
User Badges:

Please ignore the last post.


The Prolink was a GSM-BRI model and I am using my FXO Cards so I need to get a replacement unit.

I am happy enough that my config is ok.


Paul.

Actions

This Discussion