07-14-2010 05:32 AM - edited 03-15-2019 11:42 PM
Hi,
I am new enough to Cisco Ip telephony but managed to get a second FXO card configured on my Solution this morning (CME)
I have some mobile pro-links and would like to have the Call Manager take all calls with a cell phone prefix and send them to specific ports on my FXO card.
Does anybody know how this can be done?
Best Regards,
Paul.
Solved! Go to Solution.
07-14-2010 06:45 AM
You would need to configure dial peers that match the prefix such as:
dial-peer voice 1 pots
destination-pattern 9123456....
forward-digits 10
port 0/0/0
Probably going to need several dial peers to accomplish this.
Hope this helps.
Brandon
07-14-2010 06:45 AM
You would need to configure dial peers that match the prefix such as:
dial-peer voice 1 pots
destination-pattern 9123456....
forward-digits 10
port 0/0/0
Probably going to need several dial peers to accomplish this.
Hope this helps.
Brandon
07-14-2010 07:53 AM
Hey Brandon,
Thanks a million for this. I had to tweak it slowly as I am using dial peers in Ireland.
I need to plug in the mobile links now and test.
thanks again,
Paul.
07-15-2010 03:27 AM
Hey Brandon,
I have the card up runnign and its handling calls as part of my hunting group though I am trying to configure two physical POTS ports on the FXo card to route all cell phone traffic when available. Below is the config I have added for the card and for the call treatment.
voice-port 0/2/0
trunk-group FXO_GROUP 5
connection plar 6001
caller-id enable
!
voice-port 0/2/1
trunk-group FXO_GROUP 6
connection plar 6001
caller-id enable
!
voice-port 0/2/2
trunk-group FXO_GROUP 7
connection plar 6001
caller-id enable
!
voice-port 0/2/3
trunk-group FXO_GROUP 8
connection plar 7099
caller-id enable
!
!
dial-peer voice 2000 pots
trunkgroup FXO_GROUP 9
destination-pattern 9T
!
dial-peer voice 2001 pots
trunkgroup FXO_GROUP 10
destination-pattern 999
prefix 999
Dial peer to direct cell Phone calls to the Prolinks.
dial-peer voice 3000 pots
destination-pattern 9086........
forward-digits all
port 0/2/2
dial-peer voice 3001 pots
destination-pattern 9087........
forward-digits all
port 0/2/2
dial-peer voice 3001 pots
destination-pattern 9085........
forward-digits all
port 0/2/2
dial-peer voice 3001 pots
destination-pattern 9083........
forward-digits all
port 0/2/2
dial-peer voice 3000 pots
destination-pattern 9086........
forward-digits all
port 0/2/3
dial-peer voice 3001 pots
destination-pattern 9087........
forward-digits all
port 0/2/3
dial-peer voice 3001 pots
destination-pattern 9085........
forward-digits all
port 0/2/3
dial-peer voice 3001 pots
destination-pattern 9083........
forward-digits all
port 0/2/3
Any ideas on this?
paul.
07-15-2010 04:47 AM
Please ignore the last post.
The Prolink was a GSM-BRI model and I am using my FXO Cards so I need to get a replacement unit.
I am happy enough that my config is ok.
Paul.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide