07-14-2010 05:32 AM - edited 03-15-2019 11:42 PM
Hi,
I am new enough to Cisco Ip telephony but managed to get a second FXO card configured on my Solution this morning (CME)
I have some mobile pro-links and would like to have the Call Manager take all calls with a cell phone prefix and send them to specific ports on my FXO card.
Does anybody know how this can be done?
Best Regards,
Paul.
Solved! Go to Solution.
07-14-2010 06:45 AM
You would need to configure dial peers that match the prefix such as:
dial-peer voice 1 pots
destination-pattern 9123456....
forward-digits 10
port 0/0/0
Probably going to need several dial peers to accomplish this.
Hope this helps.
Brandon
07-14-2010 06:45 AM
You would need to configure dial peers that match the prefix such as:
dial-peer voice 1 pots
destination-pattern 9123456....
forward-digits 10
port 0/0/0
Probably going to need several dial peers to accomplish this.
Hope this helps.
Brandon
07-14-2010 07:53 AM
Hey Brandon,
Thanks a million for this. I had to tweak it slowly as I am using dial peers in Ireland.
I need to plug in the mobile links now and test.
thanks again,
Paul.
07-15-2010 03:27 AM
Hey Brandon,
I have the card up runnign and its handling calls as part of my hunting group though I am trying to configure two physical POTS ports on the FXo card to route all cell phone traffic when available. Below is the config I have added for the card and for the call treatment.
voice-port 0/2/0
trunk-group FXO_GROUP 5
connection plar 6001
caller-id enable
!
voice-port 0/2/1
trunk-group FXO_GROUP 6
connection plar 6001
caller-id enable
!
voice-port 0/2/2
trunk-group FXO_GROUP 7
connection plar 6001
caller-id enable
!
voice-port 0/2/3
trunk-group FXO_GROUP 8
connection plar 7099
caller-id enable
!
!
dial-peer voice 2000 pots
trunkgroup FXO_GROUP 9
destination-pattern 9T
!
dial-peer voice 2001 pots
trunkgroup FXO_GROUP 10
destination-pattern 999
prefix 999
Dial peer to direct cell Phone calls to the Prolinks.
dial-peer voice 3000 pots
destination-pattern 9086........
forward-digits all
port 0/2/2
dial-peer voice 3001 pots
destination-pattern 9087........
forward-digits all
port 0/2/2
dial-peer voice 3001 pots
destination-pattern 9085........
forward-digits all
port 0/2/2
dial-peer voice 3001 pots
destination-pattern 9083........
forward-digits all
port 0/2/2
dial-peer voice 3000 pots
destination-pattern 9086........
forward-digits all
port 0/2/3
dial-peer voice 3001 pots
destination-pattern 9087........
forward-digits all
port 0/2/3
dial-peer voice 3001 pots
destination-pattern 9085........
forward-digits all
port 0/2/3
dial-peer voice 3001 pots
destination-pattern 9083........
forward-digits all
port 0/2/3
Any ideas on this?
paul.
07-15-2010 04:47 AM
Please ignore the last post.
The Prolink was a GSM-BRI model and I am using my FXO Cards so I need to get a replacement unit.
I am happy enough that my config is ok.
Paul.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: