07-15-2010 03:02 PM - edited 03-04-2019 09:05 AM
I have router 7609 Version 12.2(33)SRC, but when i try to execute de command:
interface Serial3/0/0
frame-relay traffic-shaping
i can´t execute.
This version don´t support that command?
Configuration:
interface Serial3/0/0
mtu 1500
no ip address
encapsulation frame-relay IETF
logging event subif-link-status
logging event dlci-status-change
framing g751
dsu bandwidth 34010
dsu mode 1
no frame-relay inverse-arp
frame-relay lmi-type ansi
end
-------------------------------------------------------------
-------------------------------------------------------------
IOS Version:
Router1#sh ver
Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVENTERPRISEK9-M), Version 12.2(33)SRC, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 11-Jan-08 16:04 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)
Router1 uptime is 1 week, 4 days, 6 hours, 21 minutes
Uptime for this control processor is 1 week, 4 days, 6 hours, 19 minutes
System returned to ROM by reload (SP by reload)
System restarted at 09:54:42 VEN Sun Jul 4 2010
System image file is "disk0:c7600s72033-adventerprisek9-mz.122-33.SRC.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco CISCO7609 (R7000) processor (revision 1.2) with 983008K/65536K bytes of memory.
Processor board ID FOX1003026X
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Enhanced FlexWAN controller (2 Serial).
4 Virtual Ethernet interfaces
100 Gigabit Ethernet interfaces
2 Serial interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
------------------------------------------------------
------------------------------------------------------
Line Command:
Router1(config-if)#frame-relay ?
accounting Special accounting instruction
address-reg ELMI address registration
broadcast-queue Define a broadcast queue and transmit rate
class Define a map class on the interface
congestion-management Enable Frame Relay congestion management
de-group Associate a DE group with a DLCI
fast-restart fast restart on switchover
fragment Enable end-to-end fragmentation for all PVCs
ifmib-counter64 Support IF-MIB's total packet/byte counts of Counter64
on FR if/subif when main interface's ifSpeed < 20 Mbps
interface-dlci Define a DLCI on an interface/subinterface
intf-type Configure a FR DTE/DCE/NNI interface
inverse-arp Enable/disable FR inverse ARP
ip Frame Relay Internet Protocol config commands
lapf set LAPF parameter
lmi-n391dte set full status polling counter
lmi-n392dce LMI error threshold
lmi-n392dte LMI error threshold
lmi-n393dce set LMI monitored event count
lmi-n393dte set LMI monitored event count
lmi-t392dce set DCE polling verification timer
lmi-type Use CISCO-ANSI-CCITT type LMI
local-dlci Set source DLCI when LMI is not supported
map Map a protocol address to a DLCI address
multicast-dlci Set DLCI of a multicast group
policing Enable Frame Relay policing
priority-dlci-group Define a priority group of DLCIs
qos-autosense enable QOS autosense
svc Enable frame relay SVCs
traps-maximum set max traps FR generates at link up or when getting
LMI Full Status message
vc-bundle configure a frame-relay vc-bundle
Router1(config-if)#frame-relay
07-15-2010 03:13 PM
Hi,
It is not supported on flex WAN modules:
Unsupported features | •Frame Relay traffic shaping (FRTS), ISDN, Frame Relay switching, Layer 2 Tunneling Protocol (L2TP), Layer 2 Forwarding (L2F), Point-to-Point Tunneling Protocol (PPTP) |
Have a look at this doc for more info:
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_data_sheet09186a00801df1d9.html
HTH
Reza
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: