I've a cable modem attached to the WAN interface (FE4) of a new 861W. The interface is configured as a dhcp client.The WAN LED does not come on when the router is attached to the modem. What am I doing wrong?
Using 4227 out of 262136 bytes
!
! Last configuration change at 18:22:40 CST Sun Feb 28 1993 by admin
!
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname 861W
!
boot-start-marker
boot-end-marker
!
logging buffered 51200
logging console critical
enable secret 5 $1$fT/U$UBWQYmc.cNTE.aZjnKT5E.
!
no aaa new-model
memory-size iomem 10
clock timezone CST -6
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
!
crypto pki trustpoint TP-self-signed-460023439
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-460023439
revocation-check none
rsakeypair TP-self-signed-460023439
!
!
crypto pki certificate chain TP-self-signed-460023439
certificate self-signed 01 nvram:IOS-Self-Sig#1.cer
no ip source-route
ip dhcp excluded-address 10.10.10.1 10.10.10.99
ip dhcp excluded-address 192.168.1.1 192.168.1.99
!
ip dhcp pool ccp-pool1
import all
network 192.168.1.0 255.255.255.0
dns-server 209.18.47.61 209.18.47.62
default-router 192.168.1.1
domain-name specterinstruments.local
lease 0 2
!
!
ip cef
no ip bootp server
ip domain name specterinstruments.local
ip name-server 209.18.47.61
ip name-server 209.18.47.62
!
!
license udi pid CISCO861W-GN-A-K9 sn FTX14208243
!
!
username admin privilege 15 secret 5 $1$nSfP$tGrUQM4cJLbR6x2QhCyCX1
!
!
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
!
!
!
!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
description $ES_WAN$$FW_OUTSIDE$
ip address dhcp client-id FastEthernet4
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
!
interface wlan-ap0
description Service module interface to manage the embedded AP
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
!
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 192.168.1.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
!
interface Vlan2
ip address 10.10.2.1 255.255.255.0
!
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip nat inside source list 1 interface FastEthernet4 overload
!
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
no cdp run
!
control-plane
!
banner exec ^C
% Password expiration warning.
-----------------------------------------------------------------------
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
-----------------------------------------------------------------------
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
!
line con 0
login local
no modem enable
transport output telnet
line aux 0
login local
transport output telnet
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
