Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
2830
Views
0
Helpful
5
Replies

T1 configuration problem

Go to solution
martin.bednar
Level 1
Level 1

‎07-30-2010 03:06 PM - edited ‎03-04-2019 09:15 AM

Hello everyone

I have T1 HWIC in slot 2 and T1 Network module in slot 2 . Router is 3845.

If I configure first HWIC T1 for channel-group 0 timeslots 1-24 speed 64 then I'm not able to configure Module T1. I'm getting this error:

Router(config-controller)#channel-group 0 timeslots 1-24 speed 64
%Insufficient resources to create channel group
Router(config-controller)#
*Jul 30 21:52:23.111:  No Free HDLC resources (8)

If I configure first Module then I'm not able to configure HWIC. Do you know why ? Are they sharing some resources ?

Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions

Go to solution
Nagaraja Thanthry
Cisco Employee
Cisco Employee
In response to martin.bednar

‎07-31-2010 08:45 AM

Hello,

NM-HDV module supports a maximum of 32 HDLC channels with a bandwidth of 2

Mbps. So, when you configure timeslots, since you have already configured 24

slots on one card, you can at the maximum support 8 on the second.

http://www.cisco.com/en/US/docs/ios/12_3t/12_3t7/feature/guide/hdd_vfnm.html

http://www.cisco.com/warp/public/cc/pd/rt/ps282/prodlit/guido_ds.pdf

Data Features (Only Supported on NM-HD-2VE)

. Support serial data WAN access using T1/E1 or fractional T1/E1 network

interface

. N X 64 Kbps or N X 56 Kbps channel group data rates (T1:N=1 to 24, E1:N=1

to 31)

. Supports up to 32 data channel groups with a total bandwidth of up to 2

Mbps

. Supports integrated data WAN access and DS-0 voice channels on the same

T1/E1

Hope this answers your questions.

Regards,

NT

View solution in original post

0 Helpful
5 Replies 5

Go to solution
Nagaraja Thanthry
Cisco Employee
Cisco Employee

‎07-30-2010 06:06 PM

Hello,

Looks like you may not have enought DSP resources. Please use the following tool to calculate the optimal resource requirement.

http://www.cisco.com/cgi-bin/Support/DSP/cisco_prodsel.pl

You would need Cisco ID to use this tool.

Hope this helps.

Regards,

NT

0 Helpful

Go to solution
jean.moncada
Level 1
Level 1

‎07-30-2010 09:02 PM

You may have independent clocking configured, if you do then the controller will only support one channel group.

Jean Paul Moncada

0 Helpful

Go to solution
martin.bednar
Level 1
Level 1

‎07-31-2010 03:20 AM

Thank you for your help

I have to types of cards in router: NM-HDV2-2T1/E1 and VWIC2-2MFT-T1/E1. Let’s say I want to configure Network Module in slots 3/0, 3/1 and VWIC in slots 3/0/0 and 3/0/1.

If I start with configuration of VWIC, I’m not able to configure Network Module:

Router(config)#controller t1 3/0/0

Router(config-controller)#channel-group 0 timeslots 1-24

Router(config-controller)#controller t1 3/0/

*Jul 31 09:48:06.829: %LINK-3-UPDOWN: Interface Serial3/0/0:0, changed state to down

*Jul 31 09:48:07.829: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0/0:0, changed state to down

Router(config-controller)#controller t1 3/0/1

Router(config-controller)#channel-group 0 timeslots 1-24

Router(config-controller)#controller t1 3/0

*Jul 31 09:48:12.797: %LINK-3-UPDOWN: Interface Serial3/0/1:0, changed state to down

*Jul 31 09:48:13.797: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0/1:0, changed state to down

Router(config-controller)#controller t1 3/0

Router(config-controller)#channel-group 0 timeslots 1-24

%Insufficient resources to create channel group

Router(config-controller)#

*Jul 31 09:48:16.469:  No Free HDLC resources (8)

But if I remove channel-group from VWIC I’m able to configure Network Module:

Router(config-controller)#controller t1 3/0/1

Router(config-controller)#no cha

Router(config-controller)#no channel-group 0

Router(config-controller)#controller t1 3/0

Router(config-controller)#channel-group 0 timeslots 1-24

Router(config-controller)#

And this is what I don’t understand. I thought that if NM-HDV2-2T1/E1 can create only 1 full T1 channel group then I will be able to create 2 full T1 with VWIC2-2MFT-T1/E1 and 1 full T1 with NM-HDV2-2T1/E1. But I’m only able to create 2 full T1s and it doesn’t matter if I create them on NM-HDV2-2T1/E1 or VWIC2-2MFT-T1/E1. It depends only on which card I start configuring first.

If I remove channel-group from VWIC I can have 2 full T1s on NM-HDV2-2T1/E1

Router(config)#controller t1 3/0/0

Router(config-controller)#no channel-group 0

Router(config-controller)#controller t1 3/1

Router(config-controller)#channel-group 0 timeslots 1-24

I hope you understand what I’m asking.

0 Helpful

Go to solution
Nagaraja Thanthry
Cisco Employee
Cisco Employee
In response to martin.bednar

‎07-31-2010 08:45 AM

Hello,

NM-HDV module supports a maximum of 32 HDLC channels with a bandwidth of 2

Mbps. So, when you configure timeslots, since you have already configured 24

slots on one card, you can at the maximum support 8 on the second.

http://www.cisco.com/en/US/docs/ios/12_3t/12_3t7/feature/guide/hdd_vfnm.html

http://www.cisco.com/warp/public/cc/pd/rt/ps282/prodlit/guido_ds.pdf

Data Features (Only Supported on NM-HD-2VE)

. Support serial data WAN access using T1/E1 or fractional T1/E1 network

interface

. N X 64 Kbps or N X 56 Kbps channel group data rates (T1:N=1 to 24, E1:N=1

to 31)

. Supports up to 32 data channel groups with a total bandwidth of up to 2

Mbps

. Supports integrated data WAN access and DS-0 voice channels on the same

T1/E1

Hope this answers your questions.

Regards,

NT

0 Helpful

Go to solution
martin.bednar
Level 1
Level 1
In response to Nagaraja Thanthry

‎08-02-2010 06:41 AM

Thank you for explanation

0 Helpful
Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card