08-10-2010 07:07 AM - edited 03-06-2019 12:24 PM
Hi everybody,
i´m new ccna IT,
In my network, we use the routeur to make some Acl for Internet or other protocole !
u can see one of my configuration:
interface FastEthernet0/0
description INTERNAL INF
ip address 10.20.1.X 255.255.255.0
ip nat inside
duplex auto
speed auto
!
interface FastEthernet0/1
description OUTSIDE INF
ip address 212.96.X.X 255.255.X.X
ip nat outside
duplex full
speed auto
no mop enabled
and i make some nat like :
ip nat inside source list 3 interface FastEthernet0/1 overload
access-list 3 permit 10.2.1.0 0.0.0.7
access-list 3 permit 10.2.10.0 0.0.0.7
access-list 3 permit 10.20.0.0 0.0.255.255
access-list 101 permit ip host 10.2.1.140 any
access-list 101 permit ip host 10.2.1.144 any
access-list 101 permit ip host 10.2.1.153 any
access-list 101 permit ip host 10.2.1.154 any
access-list 101 permit ip host 10.2.1.80 any
My question iz , for the seconde ACL "101", if it possible to make another nat overlaod like" ip nat inside source list 101 int f0/1 overload"
If there isn´t problems to have 2 nating overload ?
08-10-2010 07:14 AM
Just use one acl ie. combine acl 3 and acl 101.
Jon
08-10-2010 07:25 AM
hi jonh
Thanx for answer but,
i don understand when u say just one acl ?
u mean one acl for combin the 3 and 101 ? How?
How can i configure the nat overload ?
08-10-2010 09:34 AM
Junior
mateusjunior wrote:
hi jonh
Thanx for answer but,
i don understand when u say just one acl ?
u mean one acl for combin the 3 and 101 ? How?
How can i configure the nat overload ?
Junior
I personally like to use extended acls (ie numbers 100 - 199) so change your this in your config -
access-list 3 permit 10.2.1.0 0.0.0.7
access-list 3 permit 10.2.10.0 0.0.0.7
access-list 3 permit 10.20.0.0 0.0.255.255
access-list 101 permit ip host 10.2.1.140 any
access-list 101 permit ip host 10.2.1.144 any
access-list 101 permit ip host 10.2.1.153 any
access-list 101 permit ip host 10.2.1.154 any
access-list 101 permit ip host 10.2.1.80 any
to
access-list 101 permit 10.2.1.0 0.0.0.7 any
access-list 101 permit 10.2.10.0 0.0.0.7 any
access-list 101 permit 10.20.0.0 0.0.255.255
access-list 101 permit ip host 10.2.1.140 any
access-list 101 permit ip host 10.2.1.144 any
access-list 101 permit ip host 10.2.1.153 any
access-list 101 permit ip host 10.2.1.154 any
access-list 101 permit ip host 10.2.1.80 any
and then change -
ip nat inside source list 3 interface FastEthernet0/1 overload
to
ip nat inside source list 101 inteface fa0/1 overload
Jon
08-10-2010 09:50 AM
Realy thanx Jone
I do this ! and it walk !
And one thing that wasn´t understand, that my connection was very fat right now......Thanx to u
08-10-2010 03:55 PM
Hi Jon,
Great seeing your tips to Junior. I enjoyed reading the post.
Please help me with a scenario below:
I have an Apple Time Capsule gateway and port mapping is configured. However, I have to replace the Time Capsule with a Cisco 1841 router. I am stuck with how to transfer the current port mappings on the Time Capsule to the Cisco router.
At the moment, my current ACL & PAT configuration on the router are as below:
ip nat pool office 212.xxx.xxx.2x0 212.xxx.xxx.2x0 netmask 255.255.255.252
access-list 10 permit 10.0.1.0 0.0.0.255
access-list 10 permit 172.16.1.0 0.0.0.255
access-list 10 permit 192.168.2.0 0.0.0.255
ip nat inside source list 10 interface fa0/0 overload
!!int fa0/0 is configured with 212.xxx.xxx.2x0
Grateful for any response.
Regards,
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: