cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2646
Views
10
Helpful
5
Replies

can't dial out a specific 800 number

hello, we have ucm 7.1.3 and a 2921 as a voice gateway

when we try to make calls to a specific toll free number we get a fast busy and if i debug the pri this is the reason code of the disconnect

*Aug 16 16:29:56.675: ISDN Se0/2/0:23 Q931: RX <- PROGRESS pd = 8  callref = 0x8890
        Progress Ind i = 0x8388 - In-band info or appropriate now available
*Aug 16 16:29:56.931: ISDN Se0/2/0:23 Q931: RX <- PROGRESS pd = 8  callref = 0x8890
        Cause i = 0x83AF - Resource unavailable, unspecified
        Progress Ind i = 0x8381 - Call not end-to-end ISDN, may have in-band info
sm-r2-core-rtr(config)#
*Aug 16 16:30:01.287: ISDN Se0/2/0:23 Q931: TX -> DISCONNECT pd = 8  callref = 0x0890
        Cause i = 0x8090 - Normal call clearing
*Aug 16 16:30:01.335: ISDN Se0/2/0:23 Q931: RX <- RELEASE pd = 8  callref = 0x8890
*Aug 16 16:30:01.339: ISDN Se0/2/0:23 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x0890
sm-r2-core-rtr(config)#
*Aug 16 16:30:02.975: ISDN Se0/2/1:23 Q931: RX <- DISCONNECT pd = 8  callref = 0x888B
        Cause i = 0x8090 - Normal call clearing
*Aug 16 16:30:02.975: ISDN Se0/2/1:23 Q931: TX -> RELEASE pd = 8  callref = 0x088B
*Aug 16 16:30:02.995: ISDN Se0/2/1:23 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x888B
sm-r2-core-rtr(config)#do un all

5 Replies 5

paolo bevilacqua
Hall of Fame
Hall of Fame

Check calling number plan/type. Must be isdn/national 10 digits.

In teh future, always include the complete call setup trace, not just what you deem is relevant.

bruce.williams
Level 1
Level 1

We are having the exact same issue. We are having a problem dialing only specific 800 numbers. We are receiving the same error code.

Jul 22 11:56:26.060: ISDN Se0/0/1:23 Q931: RX <- PROGRESS pd = 8  callref = 0x8032

        Cause i = 0x83AF - Resource unavailable, unspecified

        Progress Ind i = 0x8381 - Call not end-to-end ISDN, may have in-band info

HOU2851#

Please tell me how you resolved this.

Bruce

Toll free numbers are unique in their handling requirements.  If you have both local telco connections and dedicated LD connections, you will find that you can hand of *SOME* toll free traffic, but not all, on the dedicated LD circuit.

The reason for this is that unless the LD carrer you are attached to is servicing that 800 number, they will have no idea where to send it. 

Toll free calls should be routed out via the LOCAL telco connection.  The local telco can do a lookup to see who the toll free number is PIC'ed to, and forward it to the appropriate LD carrier for termination.

If you send it to the LD carrier, and they don't terminate that 800 number (i.e. another carrier is servicing it), you'll get the error you are describing.

Cliff

Please rate helpful posts    

Also, some toll free numbers are restricted in that they can only be dialed from certain areas.  If you hit a restriction like this, you very well might see this error as well.

Cliff

Thanks we will check into that

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: