08-24-2010 04:49 AM - edited 03-21-2019 02:54 AM
Hi Guys,
I am having problems with using FAC on the UC520.
I have two ephone-dn's. One that is supposed to enter the authorization code and the other that is a vip caller (no auth codes).
I am able to get the prompt for the user that is restricted and once entered correctly the outgoing called is dialed. However the problem is that I am also getting the prompt for the ephone that is setup to be the vip caller. I've tried several different scenarios but can't seem to get it work.
Essentially my goal is such that vip caller hits the 60 pots dial peer immediately and the auth code call hits the 5500 voip dial peer then once entered correctly goes to the 60 pots dial peer.
Thanks for any assistance in advance.
Below is my config:
dial-peer cor custom
name internal
name local
name local-fac
!
dial-peer cor list call-internal
member internal
!
dial-peer cor list call-local
member local
!
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
!
dial-peer cor list call-local-fac
member local-fac
!
dial-peer cor list user-local-fac
member internal
member local-fac
!
application
service clid_authen_collect
param uid-len 3
param pin-len 3
!
aaa new-model
aaa authentication login h323 local
aaa authorization exec h323 local
aaa authorization network h323 local
!
username 201 password 123
username 201 autocommand exit
!
dial-peer voice 5500 voip
corlist incoming call-local-fac
description Local Calls
service clid_authen_collect
destination-pattern 9[2-9]......
session target ipv4:10.1.1.1
incoming called-number 9[2-9]......
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 60 pots
trunkgroup ALL_FXO
corlist outgoing call-local-fac
description Local Calls
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
destination-pattern 9[2-9]......
forward-digits all
no sip-register
!
ephone-dn 10
corlist outgoing user-local
!
ephone-dn 12
corlist outgoing user-local-fac
Solved! Go to Solution.
08-24-2010 08:10 AM
Try making these changes and test-
ephone-dn 10
corlist incoming user-local
ephone-dn 12
corlist incoming user-local-fac
dial-peer voice 5500 voip
corlist outgoing call-local-fac
corlist incoming call-local
dial-peer voice 60 pots
corlist outgoing call-local
Thanks,
Anthony
08-24-2010 08:10 AM
Try making these changes and test-
ephone-dn 10
corlist incoming user-local
ephone-dn 12
corlist incoming user-local-fac
dial-peer voice 5500 voip
corlist outgoing call-local-fac
corlist incoming call-local
dial-peer voice 60 pots
corlist outgoing call-local
Thanks,
Anthony
08-24-2010 10:45 AM
Hi Anthony,
Thanks for the response.
This actually did work. The main problem was the fact that under the dn's I had put outgoing instead of incoming (lack of sleep, I think).
BTW, If I wanted to do this same process with the international dial-peer, how is the best way to handle the ephone-dn's in this case? We have 9011T and 91[2-9][2-9][2-9]....... as international numbers here.
Thanks again for the assistance.
08-24-2010 11:16 AM
I'll take a closer look and get back to you
(mobile)
08-24-2010 05:58 PM
Added user-international under the vip callers ephone-dn
Remaining users won't really need to dial international calls out.
Thanks again Anthony.
Best Regards.
08-24-2010 08:53 PM
When I first read this post on my mobile this afternoon I thought the previous recommendations didn't fix the issue. Good to hear you're all set.
Thanks,
Anthony
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: