cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1940
Views
5
Helpful
4
Replies

Query regarding wrr-queue on 6500

mangesh.kamble
Level 1
Level 1

Hello All,

I am new to this community so please excuse in case I do some mistake.

My query is regarding wrr-queue to be configured on 6500. Now my requirement is like I want to give Voice and Video high priority and if possible need to configure Buffer(Optional). As adding buffer will add delay it is not recommended but still would require expert suggestions from your end.

I tried configuring policy-map on 6500 but it was not supporting it there was some egress and ingress queues present with which we were not comfortable.

I thought of configuring something like as mentioned below:-

mls qos

interface gig 0/1

wrr-queue cos-map 1 5 6 7

wrr-queue cos-map 2 3 4

wrr-queue cos-map 3 2

wrr-queue cos-map 4 1

priority-queue out

exit

Please correct me in ase I am doing some mistake.

My cofusion lies in cos-map 6 and 7 which actually applies for Control-plane traffic and also in the priority-queue do I need to map the particular queue there or it will automatically map it to queue 1 of wrr.

Also after enabling mpls qos will it automatically map appropriate cos values to voice and Video or I need to do it maually.

Please help.

Thanks and Regards,

Mangesh.

2 Accepted Solutions

Accepted Solutions

Lei Tian
Cisco Employee
Cisco Employee

Hi Mangesh,

The QoS setting for 6500 is different on each line card, and the default cos to queue map is based on the line card you using. For example 6548 has 1p3q1t, the default cos mapping is

Q1 COS 0,1
Q2 COS 2,3,4
Q 3 COS 6,7
Q4 strict-priority queue COS 5

For the configuration example and recommendation, you can use qos design guide as reference.

http://www.cisco.com/en/US/docs/solutions/Enterprise/WAN_and_MAN/QoS_SRND/QoSDesign.html#wp1001286

Regards,

Lei Tian

View solution in original post

Hi,

Below is excerpt from Cisco for queuing supported on 6500 line cards

This table lists all the modules and the queue types in the Rx and Tx       side of the interface or port:

Module

Rx Queues

Tx Queues

WS-X6K-S2-PFC2

1p1q4t

1p2q2t

WS-X6K-SUP1A-2GE

1p1q4t

1p2q2t

WS-X6K-SUP1-2GE

1q4t

2q2t

WS-X6501-10GEX4

1p1q8t

1p2q1t

WS-X6502-10GE

1p1q8t

1p2q1t

WS-X6516-GBIC

1p1q4t

1p2q2t

WS-X6516-GE-TX

1p1q4t

1p2q2t

WS-X6416-GBIC

1p1q4t

1p2q2t

WS-X6416-GE-MT

1p1q4t

1p2q2t

WS-X6316-GE-TX

1p1q4t

1p2q2t

WS-X6408A-GBIC

1p1q4t

1p2q2t

WS-X6408-GBIC

1q4t

2q2t

WS-X6524-100FX-MM

1p1q0t

1p3q1t

WS-X6324-100FX-SM

1q4t

2q2t

WS-X6324-100FX-MM

1q4t

2q2t

WS-X6224-100FX-MT

1q4t

2q2t

WS-X6548-RJ-21

1p1q0t

1p3q1t

WS-X6548-RJ-45

1p1q0t

1p3q1t

WS-X6348-RJ-21

1q4t

2q2t

WS-X6348-RJ21V

1q4t

2q2t

WS-X6348-RJ-45

1q4t

2q2t

WS-X6348-RJ-45V

1q4t

2q2t

WS-X6148-RJ-45V

1q4t

2q2t

WS-X6148-RJ21V

1q4t

2q2t

WS-X6248-RJ-45

1q4t

2q2t

WS-X6248A-TEL

1q4t

2q2t

WS-X6248-TEL

1q4t

2q2t

WS-X6024-10FL-MT

1q4t

2q2t

http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a00801091a5.shtml

To check it on IOS use

>sh mls qos inter x/y queuing or sh mls qos int x/yor sh int x/y queuing

HTH

Hitesh Vinzoda


Pls rate useful posts

View solution in original post

4 Replies 4

Lei Tian
Cisco Employee
Cisco Employee

Hi Mangesh,

The QoS setting for 6500 is different on each line card, and the default cos to queue map is based on the line card you using. For example 6548 has 1p3q1t, the default cos mapping is

Q1 COS 0,1
Q2 COS 2,3,4
Q 3 COS 6,7
Q4 strict-priority queue COS 5

For the configuration example and recommendation, you can use qos design guide as reference.

http://www.cisco.com/en/US/docs/solutions/Enterprise/WAN_and_MAN/QoS_SRND/QoSDesign.html#wp1001286

Regards,

Lei Tian

Dear Lei,

Thanks for your valuable reply and information. This is something truly new to me, never seen before.

I have one more query regarding same, and that is how can one check what the linecard preferring? I mean which linecard follows which queuing and dropping options.. and also how to check on CLI the same? I am using normal IOS on 6500.

Thanks for your reply in advance.

Thanks and Regards,

Mangesh.

Hi,

Below is excerpt from Cisco for queuing supported on 6500 line cards

This table lists all the modules and the queue types in the Rx and Tx       side of the interface or port:

Module

Rx Queues

Tx Queues

WS-X6K-S2-PFC2

1p1q4t

1p2q2t

WS-X6K-SUP1A-2GE

1p1q4t

1p2q2t

WS-X6K-SUP1-2GE

1q4t

2q2t

WS-X6501-10GEX4

1p1q8t

1p2q1t

WS-X6502-10GE

1p1q8t

1p2q1t

WS-X6516-GBIC

1p1q4t

1p2q2t

WS-X6516-GE-TX

1p1q4t

1p2q2t

WS-X6416-GBIC

1p1q4t

1p2q2t

WS-X6416-GE-MT

1p1q4t

1p2q2t

WS-X6316-GE-TX

1p1q4t

1p2q2t

WS-X6408A-GBIC

1p1q4t

1p2q2t

WS-X6408-GBIC

1q4t

2q2t

WS-X6524-100FX-MM

1p1q0t

1p3q1t

WS-X6324-100FX-SM

1q4t

2q2t

WS-X6324-100FX-MM

1q4t

2q2t

WS-X6224-100FX-MT

1q4t

2q2t

WS-X6548-RJ-21

1p1q0t

1p3q1t

WS-X6548-RJ-45

1p1q0t

1p3q1t

WS-X6348-RJ-21

1q4t

2q2t

WS-X6348-RJ21V

1q4t

2q2t

WS-X6348-RJ-45

1q4t

2q2t

WS-X6348-RJ-45V

1q4t

2q2t

WS-X6148-RJ-45V

1q4t

2q2t

WS-X6148-RJ21V

1q4t

2q2t

WS-X6248-RJ-45

1q4t

2q2t

WS-X6248A-TEL

1q4t

2q2t

WS-X6248-TEL

1q4t

2q2t

WS-X6024-10FL-MT

1q4t

2q2t

http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a00801091a5.shtml

To check it on IOS use

>sh mls qos inter x/y queuing or sh mls qos int x/yor sh int x/y queuing

HTH

Hitesh Vinzoda


Pls rate useful posts

Hi Mangesh,

The link I gave to you in my previous post has all information you need; the queueing structure for each module, the default setting and the recommendation.

Regards,

Lei Tian

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: