WAAS VIRTUAL BLADE NO STOP

smartnet_2s · ‎08-31-2010

Hi;

I have a wave 574, in test, and I am using this version waas-universal-4.2.3.7-k9, I created 3 virtual-blades and I saw that after select to blade, when select the bottom stop virtual blade, nothing happened. I did it with blade 1, blade 2 and blade 3 and nothing. The ip communication is ok, my question exist other way of the stop blade? At last version, example 4.1.5e I stopped blades with no problem.

Below are the blade's configs:

virtual-blade enable
virtual-blade 1
description VB_PORTO1
device cpu qemu64
device nic rtl8139
device disk IDE
device keyboard en-us
memory 1024
disk 40
interface 1 bridge GigabitEthernet 1/0 mac-address 00:21:D8:AC:00:8F
cpu-list 1
boot cd-image disk /local1/vbs/server_2003.iso
boot from cd-rom
autostart
exit
virtual-blade 2
description VB_PORT02
device cpu qemu64
device nic rtl8139
device disk IDE
device keyboard en-us
memory 1000
disk 40
interface 1 bridge GigabitEthernet 1/0 mac-address 00:21:D8:AB:DA:A9
cpu-list 1
boot cd-image disk /local1/vbs/server_2003.iso
boot from cd-rom
autostart
exit
virtual-blade 3
description BLADEPTA3
device cpu qemu64
device nic rtl8139
device disk IDE
device keyboard en-us
memory 1024
disk 20
interface 1 bridge GigabitEthernet 1/0 mac-address 00:21:D8:AC:2A:26
cpu-list 1
boot cd-image disk /local1/vbs/server_2003.iso
boot from cd-rom
autostart
exit

Thanks;

Fabio

smartnet_2s · ‎08-31-2010

Hi;

I researched better and saw that by cli or http mode, the use of the command timeout 0, was the only way for to stop virtual blade. I don´t know if it is a bug or error, but this workarround was my solution for problem.

Below are the commands by cli for to stop my virtual-blade:

WAEPORTO#virtual-blade 1 stop 0 , --> where 0 is timeout

This operation will IMMEDIATELY terminate the running VB

without any attempt at a clean shutdown.

Are you sure you want to proceed? [no]:yes

WAEPORTO#sh virtual-blade 1

virtual-blade 1

config:

description VB_PORTO1

device cpu qemu64

device nic rtl8139

device disk IDE

device keyboard en-us

memory 1024

disk 40

interface 1 bridge GigabitEthernet 1/0 mac-address 00:21:D8:AC:00:8F

cpu-list 1

no boot fd-image

boot cd-image disk /local1/vbs/server_2003.iso

boot from cd-rom

autostart

state:

stopped

WAEPORTO#sh virtual-blade

Virtual-blade resources:

VB Memory: 1024MiB configured, 2048MiB available.

VB Disk space: 40GiB configured, 136GiB available.

VB Image space /local1/vbs: 625MiB used, 143682MiB available

Virtual CPU(s) assigned: 1 2

Virtual-blade(s) state:

virtual-blade 1 is stopped

WAEPORTO#virtual-blade 1 start ?

<1-60> Startup delay in seconds

WAEPORTO#virtual-blade 1 start

WAEPORTO#sh virtual-blade

Virtual-blade resources:

VB Memory: 1024MiB configured, 2048MiB available.

VB Disk space: 40GiB configured, 136GiB available.

VB Image space /local1/vbs: 625MiB used, 143682MiB available

Virtual CPU(s) assigned: 1 2

Virtual-blade(s) state:

virtual-blade 1 is running

OR BY HTTP , the desription is in attached file " BY HTTP.PNG"

thanks;

Fabio

Bhavin Yadav · ‎08-31-2010

Hi Fabio,

That's right. Here is the help guide tha texplains all the options with start and stop numbers.

http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v421/configuration/guide/virtual.html

Hope this helps.

Regards.