FXS Ports in 881 IAD not getting released

Unanswered Question
Sep 2nd, 2010

Hi,

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

At this moment port 1 is having this problem. Eventually all lines stays in this state... FXSLS_WAIT_RELEASE_REQ.

UTB#sh voice call

0 -          -  -                     vpm level 1 state = FXSLS_ONHOOK

vpm level 0 state = S_UP

calling number , calling name unavailable, calling time 08/24 23:48

1 -          -  -                     vpm level 1 state = FXSLS_WAIT_RELEASE_REQ

vpm level 0 state = S_UP

calling number , calling name unavailable, calling time 08/24 21:08

2 -          -  -                     vpm level 1 state = FXSLS_ONHOOK

vpm level 0 state = S_UP

calling number , calling name unavailable, calling time 08/25 10:07

3 -          -  -                     vpm level 1 state = FXSLS_ONHOOK

vpm level 0 state = S_UP

------------------------------

here the sh ver...

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

Cisco IOS Software, C880 Software (C880VOICE-UNIVERSALK9-M), Version 12.4(20)T4, RELEASE SOFTWARE (c4)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Wed 02-Sep-09 10:27 by prod_rel_team

ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)

UTB uptime is 56 minutes

System returned to ROM by reload at 20:04:49 UTC Tue Aug 24 2010

System image file is "flash:c880voice-universalk9-mz.124-20.T4.bin"

Last reload reason: Reload Command

This is issue is repeating constantly....

Thanks for any help....

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Paolo Bevilacqua Thu, 09/02/2010 - 16:28

I am afraid you have to contact the tac for this, would try a sw update to 15(0)M3 before anyway.

Steven Holl Fri, 09/03/2010 - 06:37

What is connected to the other side of the FXS ports?  Is it a paging system (or the like) perhaps?  If so, what type of disconnect supervison is this device looking for to know that it has to go onhook?

Or is it an analog handset?

What happens if you unplug the analog device from the port, and wait 60 seconds?  Does the port go back to ONHOOK?  If so, the other side isn't going onhook.

I'm not sure if the FXS on the 881 do power denial or battery reversal off the top of my head.  At the minimum, you can configure 'timeouts call-disconnect 5' which will make the port send a re-order tone to the device when it is supposed to hang up.

But once you answer what is connected (and if it isn't a handset, what it is looking for as disconnect supervision to go onhook), then we can figure out if/how the 881's FXS can do that.

Steven Holl Fri, 09/03/2010 - 06:38

I should mention: this is only a disconnect supervision issue if the unplug test is successful.  If that doens't change the port state, then it's an IOS bug, and you want to get these debugs as we transition into a bad state:

debug voip ccapi inout

debug vpm sig

(debugs for whatever voip protocol you are running)

Actions

This Discussion