help needed for connecting cme to IPC alliance system

Unanswered Question
Sep 8th, 2010
User Badges:

Hi guys, i'm trying to implement this design but failed. Please help me to clarify what had went wrong.

w.JPG

I have a running CME 4.0 and it is working fine. What i'm going to do is pass 2 dn to IPC Alliance system. Due to insufficient card slot, I've purchased another router with VWIC-1MFT. The problem is controller E1 that i've configured in router B wont establish (down). I'm using 1-2,4-5 connector and I've tried with loopback test on router and it works fine.


router A (forward the 2 dn to router B)

dial-peer voice 6666 voip
description **forward to voice_gw**
destination-pattern 6666
session target ipv4:192.168.10.3
!
dial-peer voice 6600 voip
description **forward to voice_gw**
destination-pattern 6600
session target ipv4:192.168.10.3



sh dial-peer voice summary

6666   voip  up   up             6666               0  syst ipv4:192.168.10.3

6600   voip  up   up             6600               0  syst ipv4:192.168.10.3



router B (grab dn from router A and pass them to IPC)

clock timezone MY 8
network-clock-participate wic 0


voice-card 0


controller E1 0/0/0
framing NO-CRC4
ds0-group 1 timeslots 1-2 type e&m-melcas-immed


voice-port 0/0/0:1
!
dial-peer voice 6600 pots
destination-pattern 6600
port 0/0/0:1
prefix 6600
!
dial-peer voice 6666 pots
destination-pattern 6666
port 0/0/0:1
prefix 6666



sh controller e1
E1 0/0/0 is down.
  Applique type is Channelized E1 - balanced
  Cablelength is Unknown
  Transmitter is sending remote alarm.
  Receiver has loss of frame.
  alarm-trigger is not set
  Version info Firmware: 20090408, FPGA: 13, spm_count = 0
  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
  Data in current interval (120 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 120 Unavail Secs
  Total Data (last 3 15 minute intervals):
     17020 Line Code Violations, 24 Path Code Violations,
     4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
     4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 2650 Unavail Secs

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Felipe Garrido Wed, 09/08/2010 - 07:41
User Badges:
  • Cisco Employee,

Does the IPC system need to be connected with a straigth or cross-over E1/T1 cable? If cross-over, the pin out is 1-4 2-5. It's worth a try if you can make the cable. Also, check the framing and line code configuration and make sure they match with the IPC system.


-Felipe

limsiangchin Wed, 09/08/2010 - 18:48
User Badges:

yes it is using the crossover cable, framing and linecode is match as well. i was thinking whether the setup shouldnt be done this way  or there is a better way to do this using same hardwares.

Felipe Garrido Thu, 09/09/2010 - 08:28
User Badges:
  • Cisco Employee,

Is the pinout for the cross-over cable 1-4 2-5?


-Felipe

Mohamed Shameer... Wed, 04/24/2013 - 08:56
User Badges:

Hi


Did you manage to integrate CME with IPC alliance system

if yes, can you please share some configuration steps


Thanks

shameer

Actions

This Discussion