cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1405
Views
0
Helpful
2
Replies

How to configure CISCO ASA 5510 for internal remote desktop ?

ian_banderaz
Level 1
Level 1

Helo,I have a client that want to install new ASA (5510) in their network.

and then I did some experiment to implement it. the topology is like this :

Drawing1.jpg

--------configuration---------

2800 router :


interface FastEthernet0/0
ip address 172.16.1.1 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 192.168.11.3 255.255.255.0
duplex auto
speed auto
!

ip route 192.168.12.0 255.255.255.0 172.16.1.2

1841 router :

interface FastEthernet0/0
ip address 172.16.1.2 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 192.168.12.1 255.255.255.0
duplex auto
speed auto
!
!
ip route 0.0.0.0 0.0.0.0 172.16.1.1

ASA 5510 :

: Saved
: Written by enable_15 at 19:21:31.639 UTC Mon Sep 13 2010
!
ASA Version 8.2(1)
!
hostname ciscoasa
enable password **** encrypted
passwd ***** encrypted
names
name 192.168.12.0 Branch
dns-guard
!
interface Ethernet0/0
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.11.1 255.255.255.0
!
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
!
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
!
interface Management0/0
shutdown
no nameif
no security-level
no ip address
management-only
!
boot system disk0:/asa821-k8.bin
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list inside_access_in extended permit ip 192.168.11.0 255.255.255.0 Branch 255.255.255.0
access-list inside_access_in extended permit ip 192.168.11.0 255.255.255.0 any
access-list inside_access_in extended permit ip Branch 255.255.255.0 192.168.11.0 255.255.255.0
!
tcp-map mssmap
  synack-data allow
  invalid-ack allow
  seq-past-window allow
  urgent-flag allow
!
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
asdm location Branch 255.255.255.0 inside
no asdm history enable
arp timeout 14400
static (inside,inside) 192.168.11.2 192.168.11.2 netmask 255.255.255.255
static (inside,inside) 192.168.12.2 192.168.12.2 netmask 255.255.255.255
access-group inside_access_in in interface inside
route inside Branch 255.255.255.0 172.16.1.1 1
timeout xlate 3:00:00
timeout conn 10:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 0.0.0.0 0.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username ***** password ***** encrypted
!
class-map mymap
match access-list inside_access_in
class-map inspection_default
match default-inspection-traffic
!
!
policy-map global_policy
class inspection_default
  inspect ftp
  inspect h323 h225
  inspect h323 ras
  inspect netbios
  inspect rsh
  inspect rtsp
  inspect skinny 
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect tftp
  inspect sip 
  inspect xdmcp
policy-map myPolicy
class mymap
  set connection advanced-options mssmap
!
service-policy global_policy global
service-policy myPolicy interface inside
prompt hostname context
Cryptochecksum:a605d94f29924e5267644dd0f4476145
: end

I can successfully ping from host 192.168.12.2 to 192.168.11.2, but I can't do remote desktop from those host.

then I use wireshark to capture packet in my computer and it says that TCP ACKed Lost Segment.

"1373","164.538081","192.168.11.2","192.168.12.2","TCP","47785 > ms-wbt-server [SYN] Seq=0 Win=8192 Len=0 MSS=1460 WS=2"

"1374","164.538993","192.168.12.2","192.168.11.2","TCP","[TCP ACKed lost segment] ms-wbt-server > 47785 [RST, ACK] Seq=1 Ack=1407706213 Win=0 Len=0"

I can guarantee that both computers are remote desktop enabled and all firewall have been disabled.

please help, any suggest would be great .

thanks .

sincerley yours

-IAN WIJAYA-

2 Replies 2

ian_banderaz
Level 1
Level 1

up -_-'

seanelias
Level 1
Level 1

ear Ian_benderaz,

 

Thank god i am not alone on this ,

 

Me too having the exact same problem , i can ping to the host ,but no remote desktop .

 

Somebody please help me on this , how enable remote desktop on asa 5505 

 

Thanks 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: