Remote Button Programing

Answered Question
Sep 17th, 2010

I'm able to program the remote buttons with no problem but, i have over 60 DMPs deployed and would like to be able to program them all at once.  Is there a way in the DMM to write an advanced task app that will program the button remote?

Thanks,

Al

I have this problem too.
0 votes
Correct Answer by Tomas De Leon about 6 years 2 months ago

Try this string to set the YELLOW button and then you can use this

as a template:


irasrv.key_YELLOW=ira%20add%201%20sh%201%20YELLOW%20bg%20wget%20-q%20%22localhost%3a7777%2Fset_param%3Finit.BROWSER_CMD%3Dhttp://www.yahoo.com%22


Notice: in your string you are NOT escaping the RESERVED codes.  Per URL addressing spec RESERVED

characters need to be escaped.



I hope this clarifies this. 


Also, test your string in the browser first and then you only add the request after set_param?


Cheers!


T.

Correct Answer by Tomas De Leon about 6 years 2 months ago

Alan,


here is a tech tip that I wrote on programming the buttons on the remote via

a HTTP mib.  Just create an Advanced Task under the System task

for each colored button.  Test & verify it works on a single DMP first and

then send task for each colored button to all of the DMPs.  Once this is

completed make sure you SAVE the configuration.


If this answers your question, Please take time to mark this

discussion answered & rate the response.


Thank You!


T.



******************************


You can use DMP MIBs to reconfigure the DMP Remote Buttons.

VARIABLES
=========
  admin           = DMP Web Account Username
  default         = DMP Web Account Password
  a.b.c.d         = IP Address of DMP
  dmm.company.com = FQDN of the Digital Media Manager(DMM) Appliance

MIBS
====

** Use the Following MIB to see the CURRENT Remote Mappings

https://admin:[email protected]:7777/get_param?p=*.*&init.pop_enable=false


** Configure Buttons

RED
https://admin:[email protected]:[email protected][email protected]Dwww.cisco.com%22

GREEN
https://admin:[email protected]:[email protected][email protected]MD%3Dhttp://www.google.com%22

YELLOW
https://admin:[email protected]:[email protected][email protected]_CMD%3Dhttp://www.yahoo.com%22

BLUE
https://admin:[email protected]:[email protected][email protected]%3Dhttp://www.apple.com%22


ASSIGN A BUTTON TO CAST
https://admin:[email protected]:[email protected][email protected]Dhttp://dmm.company.com:8080/etv-flash-webapp/app/etv_24_.htm%22


** Use the Following MIB to see the NEW CONFIGURED Remote Mappings

https://admin:[email protected]:7777/get_param?p=*.*&init.pop_enable=false


** Save NEW CONFIGURED Remote Mappings on DMP

   -> Use the ADVANCED TASK to SAVE the DMP Settings.
   -> or Directly on the DMP using the DMP-DM Web Admin
   -> or HTTP MIB
         ie.
         https://admin:[email protected]:7777/set_param?mib.save=1
         https://admin:[email protected]:7777/set_param?mib.save=1&mng.reboot=1
 

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (2 ratings)
Loading.
Correct Answer
Tomas De Leon Fri, 09/17/2010 - 10:29

Alan,


here is a tech tip that I wrote on programming the buttons on the remote via

a HTTP mib.  Just create an Advanced Task under the System task

for each colored button.  Test & verify it works on a single DMP first and

then send task for each colored button to all of the DMPs.  Once this is

completed make sure you SAVE the configuration.


If this answers your question, Please take time to mark this

discussion answered & rate the response.


Thank You!


T.



******************************


You can use DMP MIBs to reconfigure the DMP Remote Buttons.

VARIABLES
=========
  admin           = DMP Web Account Username
  default         = DMP Web Account Password
  a.b.c.d         = IP Address of DMP
  dmm.company.com = FQDN of the Digital Media Manager(DMM) Appliance

MIBS
====

** Use the Following MIB to see the CURRENT Remote Mappings

https://admin:[email protected]:7777/get_param?p=*.*&init.pop_enable=false


** Configure Buttons

RED
https://admin:[email protected]:[email protected][email protected]Dwww.cisco.com%22

GREEN
https://admin:[email protected]:[email protected][email protected]MD%3Dhttp://www.google.com%22

YELLOW
https://admin:[email protected]:[email protected][email protected]_CMD%3Dhttp://www.yahoo.com%22

BLUE
https://admin:[email protected]:[email protected][email protected]%3Dhttp://www.apple.com%22


ASSIGN A BUTTON TO CAST
https://admin:[email protected]:[email protected][email protected]Dhttp://dmm.company.com:8080/etv-flash-webapp/app/etv_24_.htm%22


** Use the Following MIB to see the NEW CONFIGURED Remote Mappings

https://admin:[email protected]:7777/get_param?p=*.*&init.pop_enable=false


** Save NEW CONFIGURED Remote Mappings on DMP

   -> Use the ADVANCED TASK to SAVE the DMP Settings.
   -> or Directly on the DMP using the DMP-DM Web Admin
   -> or HTTP MIB
         ie.
         https://admin:[email protected]:7777/set_param?mib.save=1
         https://admin:[email protected]:7777/set_param?mib.save=1&mng.reboot=1
 

Correct Answer
Tomas De Leon Fri, 09/17/2010 - 12:58

Try this string to set the YELLOW button and then you can use this

as a template:


irasrv.key_YELLOW=ira%20add%201%20sh%201%20YELLOW%20bg%20wget%20-q%20%22localhost%3a7777%2Fset_param%3Finit.BROWSER_CMD%3Dhttp://www.yahoo.com%22


Notice: in your string you are NOT escaping the RESERVED codes.  Per URL addressing spec RESERVED

characters need to be escaped.



I hope this clarifies this. 


Also, test your string in the browser first and then you only add the request after set_param?


Cheers!


T.

sharpgate Sat, 09/25/2010 - 07:00

Hi Tomas,

May I know how to send an HTTP MIB request to a certain DMP to simulate a "remote" key click if I don't now have a remote handy. Say I want to test the Yellow button after it is programmed. I heared there was a remote simulator application out there but don't know how to get it?

Thanks

Actions

This Discussion