ā09-19-2010 02:20 PM - edited ā03-11-2019 11:42 AM
Please help me out here....
I am stuck, I am trying to configure my home lab and I can't seem to find out how to do the following:
Internet -->ASA5505-->3660Router-->2900XL Switch --->ASA5505--->Wireless AP
Attached is an image with a better idea of what I am wanting to do.
I have read that any router with the ASA is usless, but I would like to have the ASA just be a firewall/VPN and not much else. Any help with this would be apprciated.
***All Cisco Equipment has basic configs loaded on them, if needed I can provide a show ver.
ā09-19-2010 02:53 PM
Hello,
From the diagram, it seems like you would like to assign 192.168.1.x address all across the board. You cannot do it with a router in between. Different router interfaces should have different IP addresses. So, in your case, it could be 192.168.1.x on the LAN side of 3660 and 192.168.2.x on the firewall side.
On the ASA:
interface vlan 1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
exit
interface Ethernet 1
switchport access vlan 1
exit
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route inside 192.168.1.0 255.255.255.0 192.168.2.2
On the 3660:
interface FastEthernet 0/0
description connection to ASA5505
ip address 192.168.2.2 255.255.255.0
no shut
exit
interface FastEthernet 0/1
description connection to 2900XL
ip address 192.168.1.1 255.255.255.0
no shut
exit
ip route 0.0.0.0 0.0.0.0 192.168.2.1
In this case, you do not need to make any changes on the ASA for the outside interface or the NAT settings. You are just introducing another subnet on the inside to make sure that you do not need to change IP address settings on the LAN.
Hope this helps.
Regards,
NT
ā09-19-2010 03:18 PM
I did all the config as you stated but got this on the ASA
ASA2(config)# route inside 192.168.1.0 255.255.255.0 192.168.2.2
ERROR: Cannot add route, connected route exists
Not sure how to solve this.
ā09-19-2010 03:20 PM
Hello,
Can you post the output of "show run interface" and "show run route" commands here?
Regards,
NT
ā09-19-2010 03:42 PM
Got the route comman to go, but now not internet access. Cable modem is connected to 0/0
ASA Version 8.2(3)
!
hostname ASA2
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
!
interface Vlan5
no nameif
security-level 50
no ip address
!
ftp mode passive
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 192.168.2.0-192.168.2.36 netmask 255.255.255.0
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route inside 192.168.1.0 255.255.255.0 192.168.2.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
!
dhcpd address 192.168.2.5-192.168.2.36 inside
dhcpd dns 68.87.68.166 interface inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:1a1353fe23c3450240b068138904822d
: end
ā09-19-2010 03:50 PM
Hello,
Please remove the following line:
global (outside) 1 192.168.2.0-192.168.2.36 netmask 255.255.255.0
the command is
no global (outside) 1 192.168.2.0-192.168.2.36 netmask 255.255.255.0
That should fix the internet connection issue.
Regards,
NT
ā09-19-2010 04:11 PM
removed it, but still no internet access....looking at my ip config on the PC, my default gateway is 192.168.1.1, is that correct?
Right now I have the cable modem ---> ASA 0/0 ---> ASA 0/1 ---->Router0/0----->Router0/1---->Switch 2900XL
Router Show Run
Router#show run
Building configuration...
Current configuration : 1244 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$.7Q9$mJ4Y0sVUoAw8QZ/33g1JD/
enable password henry999
!
no aaa new-model
no ip routing
!
!
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1 192.168.1.7
ip dhcp excluded-address 192.168.1.1 192.168.1.10
!
ip dhcp pool 192.168.1.0/24
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 8.8.4.4
!
!
!
username woodjl privilege 15 secret 5 $1$w.xT$cFJweRcOx29N9hKafqu4h1
!
!
!
!
interface FastEthernet0/0
description connection to ASA5505
ip address 192.168.2.2 255.255.255.0
no ip route-cache
speed auto
full-duplex
!
interface FastEthernet0/1
description connection to 2900XL
ip address 192.168.1.1 255.255.255.0
no ip route-cache
duplex auto
speed auto
!
ip http server
ip http authentication local
ip http timeout-policy idle 600 life 86400 requests 10000
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.2.1
!
!
snmp-server community 192.168.1.1 RO
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
privilege level 15
password henry
login local
!
!
end
ā09-19-2010 04:18 PM
Hello,
Please issue the following command on the Router:
ip routing
Then, please issue the following command on the ASA:
clear xlate
This should clear out the incorrect xlate entries and allow internet connection.
Hope this helps.
Regards,
NT
ā09-19-2010 04:40 PM
still no internet.....grrr....any ideas?
ASA current show run
SA Version 8.2(3)
!
hostname ciscoasa
enable password DQucN59Njn0OjpJL encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address dhcp
!
ftp mode passive
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route inside 192.168.1.0 255.255.255.0 192.168.2.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
service-policy global_policy global
prompt hostname context
Cryptochecksum:59c3d18363d20a207a02bf8b79a27069
: end
ā09-19-2010 04:34 PM
Sorry, here is the corret show run:
Building configuration...
Current configuration : 1175 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$.7Q9$mJ4Y0sVUoAw8QZ/33g1JD/
enable password henry999
!
no aaa new-model
no ip routing
!
!
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1 192.168.1.7
ip dhcp excluded-address 192.168.1.1 192.168.1.10
!
ip dhcp pool 192.168.1.0/24
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 8.8.4.4
!
!
!
username woodjl privilege 15 secret 5 $1$w.xT$cFJweRcOx29N9hKafqu4h1
!
!
!
!
interface FastEthernet0/0
ip address 192.168.2.2 255.255.255.0
no ip route-cache
speed auto
full-duplex
!
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
no ip route-cache
duplex auto
speed auto
!
ip http server
ip http authentication local
ip http timeout-policy idle 600 life 86400 requests 10000
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.2.1
!
!
snmp-server community 192.168.1.1 RO
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
privilege level 15
password henry
login local
!
!
end
ā09-19-2010 04:46 PM
Show Run of the router after ip route command:
uilding configuration...
Current configuration : 1120 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$.7Q9$mJ4Y0sVUoAw8QZ/33g1JD/
enable password henry999
!
no aaa new-model
!
!
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1 192.168.1.7
ip dhcp excluded-address 192.168.1.1 192.168.1.10
!
ip dhcp pool 192.168.1.0/24
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 8.8.4.4
!
!
!
username woodjl privilege 15 secret 5 $1$w.xT$cFJweRcOx29N9hKafqu4h1
!
!
!
!
interface FastEthernet0/0
ip address 192.168.2.2 255.255.255.0
speed auto
full-duplex
!
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
duplex auto
speed auto
!
ip http server
ip http authentication local
ip http timeout-policy idle 600 life 86400 requests 10000
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.2.1
!
!
snmp-server community 192.168.1.1 RO
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
privilege level 15
password henry
login local
!
!
end
ā09-19-2010 05:20 PM
Hello,
Can you try pinging 192.168.2.1 from any of the inside clients? If that works, that means the connection is good. Then please try to ping 4.2.2.2 from the ASA. That tells you if you have internet connectivity from the ASA or not. On the ASA, please try the following commands:
access-list outside_access_in permit icmp any any echo-reply
access-group outside_access_in in interface outside
Hope this helps.
Regards,
NT
ā09-19-2010 05:39 PM
I can ping the ASA and Router, but I don't get a reply from the internet.....
What could be wrong?
Thanks.
ā09-19-2010 06:37 PM
Just to clarify, did you try to ping 4.2.2.2 from the ASA itself?
Can you get a "show ip" and "show route" from the ASA?
ā09-19-2010 08:55 PM
Hello,
Can you please try the following command:
icmp permit any outside
Then, try to ping 4.2.2.2 and see if that works.
Regards,
NT
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide