11-04-2011 11:57 AM - edited 03-04-2019 02:09 PM
My question is regarding assigning policy-maps to a interface.
Background:
The config I am posting is from a 2621 router. This routers Int fa0/0 connects to AT&Ts OPTEMAN 10Mbs Ethernet interface. The other end connects to our HQ router. At HQ is our PRIs and phone switches. I have configured QoS for this router, but don't I have to link them to the ingress interfacce (Int FA0/0)?
Here is the routers config:
sh run
Building configuration...
Current configuration : 1590 bytes
!
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ACCESSRTR1
!
enable secret 5 $1$oKQI$9XtW3TrwSiaCB69qaw67T1
enable password 7 0505560A2F585C1048554653
!
ip subnet-zero
ip cef
!
!
no ip domain-lookup
!
call rsvp-sync
!
!
!
--More-- !
!
!
!
class-map match-any Voice-Traffic
match ip dscp ef
class-map match-any Voice-Signal
match ip dscp cs3
match ip dscp af31
class-map match-any Video
match ip dscp af41
!
!
policy-map Voip
class Voice-Traffic
priority 20
class Voice-Signal
bandwidth percent 25
class Video
class class-default
policy-map OPTEMAN10M
class class-default
shape average 100000000 40000 0
--More-- service-policy Voip
!
!
!
interface FastEthernet0/0
description OPTEMAN ERS Interface
ip address 10.10.10.2 255.255.255.248
duplex auto
speed 10
!
interface FastEthernet0/1
description Access LAN Interface
ip address 10.133.22.1 255.255.254.0
speed 100
full-duplex
!
router eigrp 1
network 10.0.0.0
auto-summary
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.10.10.1
ip route 10.133.1.0 255.255.255.0 10.10.10.1
--More-- ip route 10.133.2.0 255.255.255.0 10.10.10.1
ip route 10.133.3.0 255.255.255.0 10.10.10.1
no ip http server
!
snmp-server community mccmh RO
snmp-server enable traps tty
!
dial-peer cor custom
!
!
!
!
line con 0
password 7 1107490019061915557A7A65
line aux 0
password 7 04555B0301355E5758495456
line vty 0
password 7 06085F24425A1B005447434A
login
line vty 1
password 7 130B4717051816337A747972
login
line vty 2 4
--More-- password 7 130E1E1C0C4B50
login
!
end
ACCESSRTR1#
-Thanks for the help
Solved! Go to Solution.
11-04-2011 01:24 PM
Hi,
of course you have to apply this policy-map to an interface otherwise it will serve no purpose.
You must apply outbound on WAN interface as you are shaping. As Joseph remarked above shaping is done if you can send at a rate higher than the access rate or CIR and the ISP is policing traffic above that rate.
Is it the case for you?
setting the bandwidth of an interface won't refrain it to send at the access rate.
Regards.
Alain
11-04-2011 05:54 PM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
interface FastEthernet0/0
service-policy Voip out (or it might be out Voip)
11-05-2011 05:24 AM
in and out is relative to the router. In this case you want to apply the policy to the traffic going out of the router toward your HQ. On the HQ end you want another policy applied out toward your remote site. You don't need a policy inbound on either router because the bottleneck is not at the router ( it is the speed of your wan).
Sent from Cisco Technical Support iPhone App
11-04-2011 12:33 PM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
If your WAN connection is only 10 Mbps and your LAN connection is 100 Mbps, you'll likely only need QoS on F0/0 egress.
PS:
If you get the full 10 Mbps on the WAN facing Ethernet there's no need to shape at 10 Mbps.
11-04-2011 12:37 PM
I will get full 10Mbs on the WAN facing Ethernet, that is why I set it's port speed to 10Mbs.
Do I need to apply andy of this to an interface:
class-map match-any Voice-Traffic
match ip dscp ef
class-map match-any Voice-Signal
match ip dscp cs3
match ip dscp af31
class-map match-any Video
match ip dscp af41
!
!
policy-map Voip
class Voice-Traffic
priority 20
class Voice-Signal
bandwidth percent 25
class Video
class class-default
policy-map OPTEMAN10M
class class-default
shape average 100000000 40000 0
11-04-2011 01:24 PM
Hi,
of course you have to apply this policy-map to an interface otherwise it will serve no purpose.
You must apply outbound on WAN interface as you are shaping. As Joseph remarked above shaping is done if you can send at a rate higher than the access rate or CIR and the ISP is policing traffic above that rate.
Is it the case for you?
setting the bandwidth of an interface won't refrain it to send at the access rate.
Regards.
Alain
11-04-2011 04:45 PM
Based on the config I provided, what commands will I use to correctly apply the policies?
11-04-2011 05:54 PM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
interface FastEthernet0/0
service-policy Voip out (or it might be out Voip)
11-04-2011 06:17 PM
pardon me for not understanding. but wouldn't that policy be 'in' not 'out'?
11-05-2011 04:30 AM
Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
If f0/0 is the MPLS connection, out is correct.
11-05-2011 09:33 AM
Hi,
you can't apply a QoS policy with shaping or CBWFQ config inbound, it must be outbound and in your case on the interface towards MPLS.
Alain
11-05-2011 05:24 AM
in and out is relative to the router. In this case you want to apply the policy to the traffic going out of the router toward your HQ. On the HQ end you want another policy applied out toward your remote site. You don't need a policy inbound on either router because the bottleneck is not at the router ( it is the speed of your wan).
Sent from Cisco Technical Support iPhone App
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: