Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
901
Views
10
Helpful
5
Replies

Cisco 7613 Input queue

adibenedetto18
Level 1
Level 1

‎12-05-2011 10:00 AM - edited ‎03-07-2019 03:44 AM

Hi,

I was wondering what could be a cause for the input queue drops and flushes number to be the same. If you have any commands I can run to do some troubleshooting that would be great. Thanks

Full-duplex, 1000Mb/s, media type is SX

  input flow-control is off, output flow-control is off

  Clock mode is auto

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 00:00:00, output 00:00:00, output hang never

  Last clearing of "show interface" counters 4d21h

  Input queue: 0/75/29981/29981 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

Labels:
0 Helpful
5 Replies 5

rsimoni
Cisco Employee
Cisco Employee

‎12-05-2011 10:10 AM

Hi,

input queue drops might indicate different problems depending on port configuration and other variable.

Can you attache the whole output  show interface x/x for us to see other important info to correlate with the input drops.

Also, do you see the drops on this port only or in others?

What about svi's do you see drops on those too?

How fast do the drop increment? Do you see a linear increment or in burts?

Besides drops and flushes do you see other counters increasing?

Riccardo

0 Helpful

adibenedetto18
Level 1
Level 1
In response to rsimoni

‎12-05-2011 10:19 AM

Show interface whole output

GigabitEthernet9/1 is up, line protocol is up (connected)

  Hardware is C6k 1000Mb 802.3, address is 001a.e31a.90c0 (bia 001a.e31a.90c0)

  Description: LAN connection

  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation 802.1Q Virtual LAN, Vlan ID  1., loopback not set

  Keepalive set (10 sec)

  Full-duplex, 1000Mb/s, media type is SX

  input flow-control is off, output flow-control is off

  Clock mode is auto

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input 00:00:00, output 00:00:00, output hang never

  Last clearing of "show interface" counters 4d21h

  Input queue: 0/75/29981/29981 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  30 second input rate 13000 bits/sec, 14 packets/sec

  30 second output rate 3000 bits/sec, 5 packets/sec

  L2 Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes

  L3 in Switched: ucast: 0 pkt, 0 bytes - mcast: 0 pkt, 0 bytes mcast

  L3 out Switched: ucast: 0 pkt, 0 bytes mcast: 0 pkt, 0 bytes

     4330076 packets input, 385044258 bytes, 0 no buffer

     Received 4207059 broadcasts (499570 IP multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 0 multicast, 0 pause input

     0 input packets with dribble condition detected

     2052579 packets output, 151433237 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 unknown protocol drops

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier, 0 pause output

     0 output buffer failures, 0 output buffers swapped out

Also, do you see the drops on this port only or in others? Only this port

What about svi's do you see drops on those too? I do not see any drops on the svi

How fast do the drop increment? Do you see a linear increment or in burts? The drops look to be burst such as 5 or 10 in a period of time

0 Helpful

Joseph W. Doherty
Hall of Fame
Hall of Fame

‎12-05-2011 11:14 AM

Disclaimer

The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.

Liability Disclaimer

In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.

Posting

Might be SPD random drops or buffer failures.

Since you're running at gig, you might also just first try increasing the size of your input queue.

0 Helpful

rsimoni
Cisco Employee
Cisco Employee
In response to Joseph W. Doherty

‎12-05-2011 12:59 PM

I am afraid that those are not SPD drops as Gi9/1 is a L2 port and on L2 interfaces input drops/flushes have a different meaning as this traffic is not destined to the RP.

On L2 ports input drops might indicat fabric related drops (fabric flow control) which on releases after CSCsk83524 are also indicated by overruns, or physical buffers problem (oversubriscption).

To narrow this down can you send

show version

show module

show run int g9/1

show interfaces | include line protocol is|Input queue| rate

Riccardo

adibenedetto18
Level 1
Level 1
In response to rsimoni

‎12-06-2011 05:46 AM

So I decided to replace the media from fiber to cat5e cable, drops seem to clear up. Thanks for your help.

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card