Logs found as port consistency Restored on switch 3550.

Unanswered Question
Dec 19th, 2011

Hi,

Please find below logs we found on switch 3550

.Dec 17 19:58:06.193: %SPANTREE-5-TOPOTRAP: Topology Change Trap for vlan 15

.Dec 17 19:58:07.190: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to down

.Dec 17 19:58:07.190: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to down

.Dec 17 19:58:08.198: %LINK-3-UPDOWN: Interface FastEthernet0/23, changed state to down

.Dec 17 19:59:18.671: %SPANTREE-5-TOPOTRAP: Topology Change Trap for vlan 15

.Dec 17 19:59:19.671: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan15, changed state to down

.Dec 17 19:59:21.727: %LINK-3-UPDOWN: Interface FastEthernet0/23, changed state to up

.Dec 17 19:59:23.731: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/23, changed state to up

.Dec 17 19:59:36.104: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking FastEthernet0/20 on VLAN0015. Port consistency restored.

.Dec 17 19:59:52.732: %SPANTREE-5-TOPOTRAP: Topology Change Trap for vlan 15

.Dec 17 19:59:53.732: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan15, changed state to up

.Dec 17 19:59:53.732: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20, changed state to up

.Dec 17 20:00:06.104: %SPANTREE-5-TOPOTRAP: Topology Change Trap for vlan 15

on date 17th dec 2011 in the mention logs,  i found suddenly the switch CE-500 (in the given diagram) goes unexpected Reload that time only we observed the above mention logs, i also find-out there is no power traps that time.

i have gone through the cisco documentation relating to type-inconsistency and PVID-inconsistency but i did not found any solution relating to port-inconsistency, help me to get this solution if any where listed. or Please help me to find out the root cause for the same.

configuration relate to Attached Diagram.

3550 config:-

--------------------

# int fa0/20

switchport access vlan 15

switchport mode access

# int fa0/23

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 192,15,20

switchport mode trunk

STP Enable as PVST

-------------------------------------

Same configuration is on port gi1 on CE500 switch

------------------------------

Dlink switch 1 config :-

# int fa0/48

vlan allowed 192,20

STP disabled

----------------------------

Dlink switch 2 config :-

# int fa0/48

access vlan 15

int Fa0/20 of  3550 is connected to int fa0/48 of D-link

Native Vlan is 1 for all

Thanx for your Support.

Attachment: 
I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Average Rating: 0 (0 ratings)

Actions

Login or Register to take actions

This Discussion

Posted December 19, 2011 at 9:27 PM
Stats:
Replies:0 Avg. Rating:
Views:991 Votes:0
Shares:0

Related Content

Discussions Leaderboard