cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1879
Views
0
Helpful
6
Replies

UC560 Remote Phone

I have a UC560 and an ASA. I have a 7945 and have it connected remotely. It registers but there is no audio. I initially was trying to get the ASA to work with the UC Phone Proxy but it wasnt working.

RIght now:

I have a remote phone connected behind a 2811 router to a UC560 behind an ASA and have no audio  (NO VPN's in play)

ANy idea what I need to do to get the audio work? Open ports, etc?

Thanks

Nathan

6 Replies 6

Also, just so someone doesnt ask.

I am not using the WAN port or VPN on the UC560. The 7945 does have 9.2.3 so it has the VPN but I am told it wont connect to the UC...

Nathan,

For your phone with SCCP (Skinny) TCP 2000

If its SIP UDP & TCP 5060

For the RTP (Speech) UDP 16384 - 32768

For a full list look here

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/multcme.html#wp1078455

HTH

Alex

Please rate useful posts

Regards, Alex. Please rate useful posts.

AC- thanks for responding!

Pardon me for being dense, but I have a static NAT for PUBLIC address to the Private address of the VLAN 1 interface on the UC560...registers, still no audio.

I added those ports to the accesslist and still nothing...

Any other thoughts/suggestions?

When doing a sh ephone register it shows coming from that same public address....am i missing something?

Nathan,

I have never configured this set up.

However looking at the SRND

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/security.html#wp1077404

I think you need to read this

You need to add:this to your remote phone


ephone 1 (Your Ephone number) mtp
codec g729r8

Regards

Alex

Regards, Alex. Please rate useful posts.

UPDATE: THIS IS WHERE I AM NOW

I have a ASA 5510 8.4(2) setup with Phone proxy and its works perfect (7945's, secure, etc)....for one call. Then the next call i have no audio (or one way sometimes).

Here is what I have come to find out:

When I make a call it works perfect, but I have to wait for the media-session to clear when running "sh phone-proxy media-sessions

ASA# sh phone-proxy media-sessions2 in use, 6 most usedMedia-session: 68.184.xxx.xxx/30004 :: client ip 50.84.xxx.xxx/26590 Lcl RTP conn 68.184.xxx.xxx/30004 to 10.1.x.x/2000 tx_pkts 872 rx_pkts 869 Rmt master key and salt 00000000000000000000000000000000 Lcl master key and salt 00000000000000000000000000000000

Media-session: 68.184.xxx.xxx/30000 :: client ip 10.1.x.x/2000 Lcl SRTP conn 68.184.xxx.xxx/30000 to 50.84.xxx.xxx/26590 tx_pkts 865 rx_pkts 872 Rmt master key and salt 8644e7924900c0bebb8eaba99ca2e1d5 Lcl master key and salt 7c9c61edf2f9c7bf03fe653cedefefc5

Once it shows 0 in use after 5 minutes or so, i can make one more call, and so on..

So my question is, is there a way to clear the session immediately? And is this a licensing problem since I am using the default 2- UC proxy licenses? And if i upgrade (approximately 6 remote phones eventually) do I need to account for multiple calls simultaneously and in a row ( as in each person makes 3 calls in a 5 minute span, do I need like 30 licenses)?

Thanks!

NH

Bump!!!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: