02-04-2012 11:00 PM
hi guys;
so here is another issue i have.
Scenario:
a switch in the north is trunking a VLAN for a client at our central site. The switch in north site is a 3560 and central site node is ASR 9000.
This vlan is extended along with few others to distribution switch (7609) and from there teh same VLAN is trunked to a 2960 device at the same site as that of ASR. The idea is to carry the vlan from teh reote site to teh ASR at our central site and then bridge it to a seperate port on ASR and hook this port up to our fibre patch panel, hence providing a service to the client connecting to us at our northern site and then getting connected to teh internet service provider via teh patch panel.
Since we can not make a port on ASR an access port, i am not sure how we can do the above mentioned interconnect.
please assisst.
regards
02-05-2012 12:03 AM
Hello Jalal,
Here the configuration example:
!
interface GigabitEthernet0/0/0/0.100 l2transport
encapsulation dot1q 100
rewrite ingress tag pop 1 symmetric
!
!
interface GigabitEthernet0/0/0/1
l2transport
!
!
l2vpn
!
bridge group cust1
bridge-domain cust1
interface GigabitEthernet0/0/0/0.100
interface GigabitEthernet0/0/0/1
!
Regards,
/A
02-06-2012 06:59 PM
Thanks alot boss...
so do i use global config mode or go to interface level (specially for bridge domain and bridge group?
regards
02-07-2012 12:18 AM
It's in global config (well, in l2vpn config mode actually):
l2vpn
bridge group
bridge-domain
for more details, check:
http://www.cisco.com/en/US/docs/ios_xr_sw/iosxr_r3.7/mpls/configuration/guide/gc37vpls.html
Best regards,
Max
02-08-2012 10:23 AM
Thanks guys. The configs just had to be modified a little as i already had a bridge group which was using the same port as an ethernet flow point.
Much appreciated!
Thanks again and regards
02-10-2012 01:11 AM
Hi jalal younus
Could you show me the final configuration you used? I have a similar case ( https://supportforums.cisco.com/message/3553558#3553558 ) and I really appreciate it.
Thank you in advance!
02-10-2012 02:40 AM
Hi,
i've replied to you in your thread.
regards,
/A
02-11-2012 11:14 AM
sure here is what i have:
interface GigabitEthernet0/2/0/34
description xxx-2
transceiver permit pid all
l2transport
!
bridge group xxx
bridge-domain xxx
interface Bundle-Ether99.526
!
interface GigabitEthernet0/2/0/34 -------------> just added this new interface to the existing bridge group.
!
interface GigabitEthernet0/2/0/33.526
so what i achieved here is that the interface Bundle-Ether99.526 acts as an EFP(where i terminate the x-connect or extended vlan from the the remote site) . I am then briding this interface with the GigabitEthernet0/2/0/3 and connecting it to the patch pannel inturn.
I hope it helps.
regards
02-13-2012 12:37 AM
Thank you very much!!
It was a great help.
Regards
01-22-2013 07:15 AM
Hi marhifer,
Please help me to configure a telnet configuration in my ASR 9k. Is this the right step for creating telnet in ASR ?
vty-pool pool1 7 80 line-template xan line template xan { |
}
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: