cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
6349
Views
0
Helpful
9
Replies

DHCPv6 on Cisco 881

indicomekt
Level 1
Level 1

Hi Guys

I am not able to activate DHCPv6 on my Cisco Router 881 (Version 15.2(2)T). There is no ipv6 dhcp ... in global config mode.

Cisco feature navigator tells me there is dhcpv6..

Router(config)#ipv6 unicast-routing

Router(config)#ipv6 cef

Router(config)#ipv6 ?

  access-list      Configure access lists

  cef                        Cisco Express Forwarding for IPv6

  flowset               Set flow label random for originated packets

  general-prefix   Configure a general IPv6 prefix

  hop-limit        Configure hop count limit

  host             Configure static hostnames

  icmp             Configure ICMP parameters

  inspect          Context-based Access Control Engine

  local            Specify local options

  nat              NAT-PT Configuration commands

  nd               Configure IPv6 ND

  neighbor         Neighbor

  port-map         Port to application mapping (PAM) configuration commands

  prefix-list      Build a prefix list

  radius           RADIUS configuration commands

  route            Configure static routes

  router           Enable an IPV6 routing process

  source-route     Process packets with source routing header options

  spd              Selective Packet Discard (SPD)

  tacacs           TACACS configuration commands

  traffic          Configure traffic parameters

  unicast-routing  Enable unicast routing

       

What's wrong with my box?

1 Accepted Solution

Accepted Solutions

Currently, the DHCPv6 server is only available in the Advanced IP services feature on the 800 series platform.

Here is the data sheet for feature to license mapping:

http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_Data_Sheet.html

I don't know if there are any plans in the future to change it, but what you are seeing today is the expected and intended behavior.

View solution in original post

9 Replies 9

sfaizul
Level 1
Level 1

I think you have some issues with your IOS licensing.

Cisco881W#show license all

Regards

syed

Router#show license all

License Store: Primary License Storage

StoreIndex: 0   Feature: advsecurity                       Version: 1.0

        License Type: Permanent

        License State: Active, In Use

        License Count: Non-Counted

        License Priority: Medium

License Store: Built-In License Storage

StoreIndex: 0   Feature: advipservices                     Version: 1.0

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

            Evaluation total period: 8  weeks 4  days

            Evaluation period left: 8  weeks 4  days

            Period used: 0  minute  0  second 

        License Count: Non-Counted

        License Priority: None

StoreIndex: 1   Feature: ios-ips-update                    Version: 1.0

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

            Evaluation total period: 8  weeks 4  days

            Evaluation period left: 8  weeks 4  days

            Period used: 0  minute  0  second 

        License Count: Non-Counted

        License Priority: None

StoreIndex: 2   Feature: WAAS_Express                      Version: 1.0

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

            Evaluation total period: 8  weeks 4  days

            Evaluation period left: 8  weeks 4  days

            Period used: 0  minute  0  second 

        License Count: Non-Counted

        License Priority: None

StoreIndex: 3   Feature: SSL_VPN                           Version: 1.0

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

            Evaluation total period: 8  weeks 4  days

            Evaluation period left: 8  weeks 4  days

            Period used: 0  minute  0  second 

        License Count: 0/0  (In-use/Violation)

        License Priority: None

I don't know wich license I need.

You are probably right.

Are you trying to be an DHCPv6 client or a DHCPv6 server?

DHCPv6 client is an interface subcommand, not a global one.  It is activated on an interface by interface basis.

http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-dhcp.html#wp1054391

DHCPv6 server is in the same license set as DHCP server (IPv4 and IPv6 should be at feature parity), so based on Feature Navigator it looks like you would need Advanced IP Services or Advanced Security license.  And you have Advanced Security.

Could be a license issue, you might want to open a TAC case.

I want to configure a DHCPv6 server. It's on global configuration mode:

http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-dhcp.html#wp1066271

DHCP Server for IPv4 is not a problem to config.

It might be  license issues.

OK, some internal experiementation indicates that in the version you run, the DHCPv6 server is available in the Advanced IP Services feature set.  You are running the Advanced Security feature set.

It is not clear to me if this state of licensing is intentional or an oversight.  I am researching that now.  Typically, Cisco products maintain parity between IPv4 and IPv6 features within a feature set.

In the interim, you should install an evaluation license for Advanced IP Services (advipservices) to activate the DHCPv6 server.

http://www.cisco.com/en/US/docs/routers/access/sw_activation/SA_on_ISR.html#wp1155619

Currently, the DHCPv6 server is only available in the Advanced IP services feature on the 800 series platform.

Here is the data sheet for feature to license mapping:

http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_Data_Sheet.html

I don't know if there are any plans in the future to change it, but what you are seeing today is the expected and intended behavior.

Thanks for the update Phillip. Is there any way we can feed this back to Cisco? It seems an unusual decision to omit DHCPv6 from the Advanced Security feature set. Especially on branch-office devices like these.

The 800 series product manager has been alerted and understands the problem, but they curently have no committed time frame to fix it.  I'll update this thread if I learn any more from them.  I also recommend filing a complaint through your sales channel and encouraging your peers with a similar issue to do the same.  Work prioritization is ultimalely driven by customer sentiment.

Hi . Any progress with problem of DHCP6 server on 88x series ?  Situation really bad because RFC 6106 also not supported by cisco . So not have another way to configure ipv6 connectivity. I am little bit wondered why such feature implemented only in ADV IP.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: