cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
4453
Views
0
Helpful
8
Replies

c4506L-E,there is only one supervisor,(Peer supervisor not detected or is not running IOS).bad,the WS-X4612-SFP-E was displayded "Unsupported module".

liuliang_dc
Level 1
Level 1

Is there any question with hardware about the WS-X4612-SFP-E modle.thanks

2 Accepted Solutions

Accepted Solutions

is there any question about "config-register = 0x2101".thanks.

No.

Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(53)SG4, RELEASE SOFTWARE (fc2)

Your IOS does NOT support the WS-X4612-SFP-E line card.  Upgrade to 12.2(54)SG or later.

View solution in original post

If the solution works, can I request if you can mark this thread as "Answered" please?

View solution in original post

8 Replies 8

Leo Laohoo
Hall of Fame
Hall of Fame

C'mon, mate.  You need to give us more info than this!

You need a minimum of Cisco IOS Software Release 12.2(54)SG or later.

**********************************************************
*                                                        *
* Welcome to Rom Monitor for WS-X45-SUP6L-E System        *
* Copyright (c) 2003-2011 by Cisco Systems, Inc.         *
* All rights reserved.                                   *
*                                                        *
**********************************************************

Checking the partition table and boot sector...
Checking FAT, Files and Directories...
Reclaiming unused space...
Updating FAT...
Rom Monitor Program Version 12.2(44r)SG10
CPU Rev: 2.1, Board Rev: 12, Board Type: 103, CPLD Nexu Rev: 14
Chassis: WS-C4506-E

Front Panel Phy is Bcm5482s
Got Mac Address: 30:e4:db:fd:ac:e1

MAC Address  : 30-e4-db-fd-ac-e1
Ip Address   : Not set.
Netmask      : Not set.
Gateway      : Not set.
TftpServer   : Not set.

Peer supervisor not detected or is not running IOS
Supervisor uplinks and all linecards have been reset


***** The system will autoboot in 5 seconds *****


Type control-C to prevent autobooting.
. . . . .

******** The system will autoboot now ********


config-register = 0x2101

Autobooting using the first file from bootflash.....

sho ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(53)SG4, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Fri 25-Feb-11 15:14 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x124334BC

ROM: 12.2(44r)SG10
Darkside Revision 4, Jawa Revision 14, Tatooine Revision 140, Forerunner Revision 1.21

Switch uptime is 1 minute
System returned to ROM by power-on
System image file is "bootflash:cat4500e-ipbase-mz.122-53.SG4.bin"

cisco WS-C4506-E (MPC8548) processor (revision 12) with 524288K bytes of memory.
Processor board ID SPE152800QF
MPC8548 CPU at 1GHz, Supervisor 6L-E
Last reset from PowerUp
1 Virtual Ethernet interface
52 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
--More--                          
--More--                           Configuration register is 0x2101

sho mod
Chassis Type : WS-C4506-E

Power consumed by backplane : 0 Watts

Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1     6  Sup 6L-E 10GE (X2), 1000BaseX (SFP)    WS-X45-SUP6L-E     JAE15300DRW
3    48  10/100/1000BaseT (RJ45)                WS-X4648-RJ45-E    JAE153805FF
5     0  Unsupported module                     WS-X4612-SFP-E     JAE15330C0I

M MAC addresses                    Hw  Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
1 30e4.db27.e840 to 30e4.db27.e845 3.0 12.2(44r)SG1 12.2(53)SG4      Ok      
3 ccef.483a.c89c to ccef.483a.c8cb 1.0                               Ok      
5 7081.0556.0fa0 to 7081.0556.0fab 1.1                               Unsupport

is there any question about "config-register = 0x2101".thanks.

is there any question about "config-register = 0x2101".thanks.

No.

Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASE-M), Version 12.2(53)SG4, RELEASE SOFTWARE (fc2)

Your IOS does NOT support the WS-X4612-SFP-E line card.  Upgrade to 12.2(54)SG or later.

liuliang_dc
Level 1
Level 1

thanks,i'll try.

If the solution works, can I request if you can mark this thread as "Answered" please?

ok,thanks!

Cool!  I'm happy to see the solution works. 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco