×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

UC540 CCA cant display PSTN Trunk details.

Answered Question
Mar 22nd, 2012
User Badges:

Hi

We have UC540 FXO

Installed PACKAGE IS : spa50x-30x-7-4-6.bin

Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M), Version 15.0(1)XA3a, SBTG Special


PSTN FXO port configuration as below,


!

voice-port 0/1/0

supervisory disconnect anytone

cptone GB

connection plar opx 209

impedance complex2

description Configured by CCA 4 FXO-0/1/0-OP

caller-id enable

!

voice-port 0/1/1

supervisory disconnect anytone

cptone GB

connection plar opx 209

impedance complex2

description Configured by CCA 4 FXO-0/1/1-OP

caller-id enable

!



Problem is :

(1)  When I click on PSTN, I an getting the screen(attached JPG screenshot)  "Operation in Progress, Reading PSTN trunk Configuration" and goes like  that for 10 minutes. What could be the issue ? We have 8 FXO ports and  configuration is as shown above.

(2) When I click  on some configuration (ex. VLAN) we get  "Java.lang.NullPointerException", what could be issue ? CCA version is  3.0(1)




Rgds

Rajesh

Attachment: 
Correct Answer by paolo bevilacqua about 5 years 5 months ago

These are "UC500 Software Packs", for which you can read documentation on cisco.com


As mentioned before already, UC500 run CME, and does all what that does.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
paolo bevilacqua Thu, 03/22/2012 - 09:56
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

You should update software (CAA and IOS) before anything else.

rajesh.kumar Fri, 03/23/2012 - 02:29
User Badges:

Dear Paolo Bevilacqua

We are adding E1 PRI VIC card to this Router.

If I continue configuration on CLI mode, and not using CCA for any further configuration, is there any issue?

Because device is out of warranty, Since we can't upgrade IOS and software.

Would you pls. clarify, I can still  use CLI mode to configure E1 PRI andnumber  translation pattern etc.  correct ?

We are familiar with CME configuration  and UC540 CLI is almost all similar to CME commands.

I belive E1 PRI and number translation rule/profile confiration is as exactly as CME.

Pls. suggest.


Rgds

Rajesh

rajesh.kumar Fri, 03/23/2012 - 10:54
User Badges:

Dear Paolo

I am not much familiar with upgrade of UC 540.

Is this only one file "UC540-8.2.0.zip" need to be loaded into box?, shall I get simple document to upgrade.

without upgrading software, can't I be able configure E1 PRI and DID number translation rule etc.?


Rgds

Rajesh 

Correct Answer
paolo bevilacqua Fri, 03/23/2012 - 12:04
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

These are "UC500 Software Packs", for which you can read documentation on cisco.com


As mentioned before already, UC500 run CME, and does all what that does.