×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

shape average percent on different devices

Unanswered Question
Apr 25th, 2012
User Badges:

Hello all,


I have set QoS up over many tunnel wan connections.  My problem:  Most of my tunnels are point-to-point wireless bridges that vary in bandwidth depending on the quality and distance of the shot.  To apply QoS to these interfaces at different bandwidths, I have to create multiple policy-maps on some devices.  I have two 3845s, one allows shape average percent on tunnels, the other does not. One running 15.0(1)M2and the other is 15.0(1)M3 IOS.  I have not been able to find why certain devices do not allow bandwidth percentages. I also can apply it to most of my 3825s, but not all.


Sample QoS configuration


class-map match-any VOICE-SIGNALING

match  dscp cs3

match  dscp af31

class-map match-all ROUTING-PROTOCOLS

match  dscp cs6

class-map match-all GOLD

match access-group name GOLD

class-map match-all GOLD-VOICE

match  dscp ef

match access-group name GOLD

class-map match-any SILVER-VOICE

match  dscp ef


policy-map QUEUEING-TO-WAN

class GOLD-VOICE

   priority percent 10

class SILVER-VOICE

   priority percent 5

class VOICE-SIGNALING

   bandwidth remaining percent 4

   set dscp ef

class GOLD

   bandwidth remaining percent 50

class class-default

   fair-queue

policy-map SHAPING-TO-WAN

class class-default

   shape average percent 99

   service-policy QUEUEING-TO-WAN


interface Tunnel100

description *** SAMPLE TUNNEL ***

bandwidth 8192

ip address 10.10.10.1 255.255.255.252

no ip redirects

no ip unreachables

no ip proxy-arp

ip mtu XXXX

ip tcp adjust-mss XXXX

load-interval 30

delay 100

qos pre-classify

tunnel source Serial0/2/1

tunnel destination 172.16.5.1

tunnel mode ipsec ipv4

tunnel protection ipsec profile SECURE

service-policy output SHAPING-TO-WAN

end

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Jacob Jennings Wed, 04/25/2012 - 05:20
User Badges:

I just checked again, I also cannot apply shape average percent to a 3845 running 15.0(1)M2.

Joseph W. Doherty Wed, 04/25/2012 - 10:09
User Badges:
  • Super Bronze, 10000 points or more

Disclaimer


The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.


Liability Disclaimer


In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.


Posting


You likely answered you're own question, i.e. a feature unique to a later IOS version.  (I wasn't even aware this could be done, but then I have worked with any 15.x IOSs.)


PS:

Might be a good idea to add tunnel path-mtu-discovery to your tunnel interfaces and you shouldn't need qos pre-classify (unless your doing QoS on the physical interface too and you need to examine pre-tunnel IP header info).

Jacob Jennings Thu, 04/26/2012 - 02:58
User Badges:

I agree with you about the IOS version, but why can I do it on a 3825 running 12.4.  I guess I just wanted to know when it was implemented and why it works on some routers.  It seems sporadic.

Actions

This Discussion

Related Content