Problem with an old Cisco Aironet 1100 (AP1121G-E-K9)

Unanswered Question
May 3rd, 2012


I'm trying to "resurect" an old wireless network made with Cisco Aironet 1100. One of the AP has lost its IOS (due to an error while trying to upgrade it through the web interface)

I tried to reload it with the "mode button". I can see in my TFTP server logs that the AP is downloading the IOS but nothing happens and the AP keep beeing stucked (leds are : red/green/red)

Could somebody help me to understand what's going wrong and to make it work again ?

Thx in advance


I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Leo Laohoo Thu, 05/03/2012 - 05:30

Console into the WAP and post the entire bootup process.

alain.montfranc Thu, 05/03/2012 - 06:01


I can't see any console pôrt, only the ethernet one. Shall I open the AP ?

alain.montfranc Thu, 05/03/2012 - 06:24

Just a short followup : I opened the AP. The a 5 PIN connector that could be a serial link but I don't know the pinout. Anyone knows ?

Eric Moyers Thu, 05/03/2012 - 06:45

Just out of curiousity which lights are Red, Green, Red. Do the all three show red, then green, then red?

Access the CLI through Telnet or SSH. There is a good sectio showing this in the admin guide:

Cisco Aironet 1100 Series Access Point Installation and Configuration Guide

Eric Moyers

Cisco Network Support Engineer

SBSC Wireless and Surveillance SME

CCNA, CCNA-Wireless


alain.montfranc Thu, 05/03/2012 - 06:57

The 3 leds are respectively red, green and red. There are not bliniking

As the AP does not boot (I think) so it has no IP, thus no telnet :-(

alain.montfranc Fri, 05/11/2012 - 01:04

Any idea anybody ?

maldehne Sun, 05/13/2012 - 01:59

ethernet : RED

status : Green

radio   : RED

Means NO CISCO IOS file

Check the following link that contains detailed description of LEDs :

You need to try again by following the steps:

Step 1 The static IP address of the PC on which your TFTP server software runs should be between and

Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.

Step 3 Set the timeout value on the TFTP server to 30 seconds.

Step 4 On the PC where the TFTP server is located, perform these steps:

a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.

b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.

Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.

Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.

Step 7 Disconnect power from the access point.

Step 8 Press and hold MODE while you reconnect power to the access point.

Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.

Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.

Step 11 After the access point reboots, reconfigure it using the GUI or the CLI.

If it didn't work with you given that we have no console access to jump inside and have access to ROMON you need to open TAC case and have RMA.


Please Don't forget to rate correct answers


Login or Register to take actions

This Discussion

Posted May 3, 2012 at 12:36 AM
Replies:7 Overall Rating:
Views:3665 Votes:0
Tags: wds

Related Content


Discussions Leaderboard

Rank Username Points
Scott Fella
Leo Laohoo
Stephen Rodriguez
George Stefanick
Rank Username Points
Manannalage ras...
Leo Laohoo
Freerk Terpstra
George Stefanick
Scott Fella

Trending Topics: Other Wireless Mobility

client could not be authenticated
Network Analysis Module (NAM) Products
Cisco 6500 nam
reason 440 driver failure
Cisco password cracker
Cisco Wireless mode