×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

CallForwardAll offnet-to-offnet calls failure

Unanswered Question
Jun 6th, 2012
User Badges:

Hi all,


I have a problem on ForwardAll of offnet to offnet call : if an end user make a ForwardAll on his IP Phone to his cell phone, and when he received an external call the forward can't be made but when he received an  internal call the forward works. The Block offnet to offnet Transfer Service parameter is set to false.


We have a CUCM 7.5, and 2911 gateway with PRI link to isdn.


Any help!

Best regards

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
nikshah Wed, 06/06/2012 - 03:27
User Badges:
  • Cisco Employee,

if you can send the traces for a bad call, along with calling and called party information and the forward call information.

Ayodeji Okanlawon Wed, 06/06/2012 - 03:29
User Badges:
  • Super Bronze, 10000 points or more
  • Cisco Designated VIP,

    2017 IP Telephony

Have you checked the CSS on the cfwdall. It need access to the partiton for the RP to dial out



Please rate useful posts


"I am complete in God, God completes me"

Aaziz AMHAOUCH Wed, 06/06/2012 - 03:34
User Badges:

Thanks for your replies;

the CSS on  cfwdall have access to route pattern partition as I said when end user received an internal call the forward works. I'll send the traces asap.

Aaziz AMHAOUCH Wed, 06/06/2012 - 04:08
User Badges:

here is debug isdn q931 of a call forward failure


PHONEA: A cell phone who make a call

3038: the ipphone who make a CallForwardAll to a cellphone number PHONEB

PHONEB: the cell phone of end user



*Jun  6 11:01:52.525: ISDN Se0/0/0:15 Q931: TX -> CONNECT_ACK pd = 8  callref =                                                                                         0x0C36

*Jun  6 11:01:53.545: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x218A                                                                                       

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98382

                Exclusive, Channel 2

        Calling Party Number i = 0x0180, 'PHONEA'

                Plan:ISDN, Type:Unknown

        Called Party Number i = 0x81, '3038'

                Plan:ISDN, Type:Unknown

*Jun  6 11:01:53.545: ISDN Se0/0/0:15 Q931: Received SETUP  callref = 0xA18A cal                                                                                        lID = 0x46EE switch = primary-net5 interface = User

*Jun  6 11:01:53.549: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x                                                                                        A18A

        Channel ID i = 0xA98382

                Exclusive, Channel 2

*Jun  6 11:01:53.561: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 i                                                                                        s 0x0 0x1, Calling num PHONEA

*Jun  6 11:01:53.561: ISDN Se0/0/0:15 Q931: Sending SETUP  callref = 0x0C38 call                                                                                        ID = 0x8B3B switch = primary-net5 interface = User

*Jun  6 11:01:53.561: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0C38                                                                                       

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839C

                Exclusive, Channel 28

        Calling Party Number i = 0x0181, 'PHONEA'

                Plan:ISDN, Type:Unknown

        Called Party Number i = 0x80, 'PHONEB'

                Plan:Unknown, Type:Unknown

*Jun  6 11:01:53.597: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x                                                                                        8C38

        Channel ID i = 0xA9839C

                Exclusive, Channel 28

*Jun  6 11:01:53.645: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x                                                                                        8C38

*Jun  6 11:01:53.677: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0                                                                                        x8C38

        Cause i = 0x82B9 - Bearer capability not presently authorized

*Jun  6 11:01:53.677: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x0C                                                                                        38

*Jun  6 11:01:53.693: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref =                                                                                         0x8C38

Ayodeji Okanlawon Wed, 06/06/2012 - 04:19
User Badges:
  • Super Bronze, 10000 points or more
  • Cisco Designated VIP,

    2017 IP Telephony

Please add the ff:


voice-port 0/0/0:15


bearer-cap speech


NB: Dont think this will make a difference because you are already doing speech to the telco. Just a long shot.


You can send a debug for a succesful internal call transfer and we can compare the difference..




Please rate useful posts


"I am complete in God, God completes me"

Actions

This Discussion

Related Content