×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Supervisor Hybrid Mod 6509

Unanswered Question
Jun 7th, 2012
User Badges:

hi all,


today I changed standby supervisor and MSFC, but I got this problem:


MOD_MINORFAIL:Minor problem in module 15




    Cat6509> (enable) show module test                                     test 15





Diagnostic mode: minimal   (mode at next reset: minimal)





Module 15 : 1-port Multilayer Switch Feature Card



Line Card Firmware Status for Module 15 : PASS



Port Status :

  Ports 1

  --------

        .



Line Card Diag Status for Module 15  (. = Pass, F = Fail, N = N/A, U = Untested)



Loopback Status [Reported by Module 2] :

  Ports 1

  --------

        F


And then I got this:


8.325: %IPC-5-NULL: Registering Control Port Id=0x2210003, seq = 0



-Traceback= 3044ADCC 3044AE48 301B65A4 301B6590


2 supervisors and MSFC have the same IOS:


show module



Mod Slot Ports Module-Type               Model               Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1   1    2     1000BaseX Supervisor      WS-X6K-S2-PFC2      yes standby

15  1    1     Multilayer Switch Feature WS-F6K-MSFC2        no  ok

2   2    2     1000BaseX Supervisor      WS-X6K-SUP2-2GE     yes ok

16  2    1     Multilayer Switch Feature WS-F6K-MSFC2        no  ok

3   3    8     1000BaseX Ethernet        WS-X6408A-GBIC      no  ok

4   4    8     1000BaseX Ethernet        WS-X6408A-GBIC      no  ok

5   5    8     1000BaseX Ethernet        WS-X6408A-GBIC      no  ok

6   6    48    10/100BaseTX Ethernet     WS-X6348-RJ-45      yes ok

7   7    48    10/100/1000BaseT Ethernet WS-X6148A-GE-TX     no  ok



--More--                       

Mod MAC-Address(es)                        Hw     Fw         Sw

--- -------------------------------------- ------ ---------- -----------------

1   00-1a-2f-58-48-06 to 00-1a-2f-58-48-07 6.1    7.1(1)     8.4(5)

    00-1a-2f-58-48-04 to 00-1a-2f-58-48-05

15  00-16-c7-71-1d-00 to 00-16-c7-71-1d-3f 2.9    12.1(4)E1  12.1(4)E1

2   00-09-11-e0-3f-8e to 00-09-11-e0-3f-8f 3.5    7.1(1)     8.4(5)

    00-09-11-e0-3f-8c to 00-09-11-e0-3f-8d

    00-09-7b-50-d4-00 to 00-09-7b-50-d7-ff

16  00-09-11-e9-94-40 to 00-09-11-e9-94-7f 2.2    12.1(4)E1  12.1(4)E1

3   00-09-12-60-c2-64 to 00-09-12-60-c2-6b 2.1    5.4(2)     8.4(5)

4   00-09-12-60-c0-fc to 00-09-12-60-c1-03 2.1    5.4(2)     8.4(5)

5   00-08-a4-f3-41-68 to 00-08-a4-f3-41-6f 2.1    5.4(2)     8.4(5)

6   00-09-12-62-80-c0 to 00-09-12-62-80-ef 6.1    5.4(2)     8.4(5)

7   00-1a-6c-4c-4d-e0 to 00-1a-6c-4c-4e-0f 1.5    8.4(1)     8.4(5)



Mod Sub-Type                Sub-Model           Sub-Serial  Sub-Hw Sub-Sw

--- ----------------------- ------------------- ----------- ------ ------

1   L3 Switching Engine II  WS-F6K-PFC2         SAL1102DF0H 3.5   

2   L3 Switching Engine II  WS-F6K-PFC2         SAL06152EN1 3.2   

6   Inline Power Module     WS-F6K-VPWR                     1.0    1.1(1)


I rebooted a lot of times standby supervisor and MSFC


Any idea?


Regards.

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.

Actions

This Discussion

Related Content