cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5393
Views
10
Helpful
18
Replies

Cisco ASR 9010 Copper port problem

mostakimulhuq
Level 1
Level 1

Recently we have purchased Cisco ASR 9010 router. We have setup a 1Gbps copper based SFP module in the line card. It detect the module and I have found this by using show controller. But when I coonect a RJ-45 cable between thre router and my laptop, port do not up, even I connect the cable to a cisco switch that time also it is not working. Is there any command to up this port!

Please help.

Regards,

Shuvo

18 Replies 18

Leo Laohoo
Hall of Fame
Hall of Fame

Your laptop has a triple-speed (10/100/1000BaseTx) NIC card?

robyn.byrne
Level 1
Level 1

Hi,

What model SFP are you using ? as I believe it needs to be SFP-GE-T.

Thanks

RJ

try enabling autonegociation with:

no duplex

no speed

on the switch side try:

duplex full

if the SPF is ok it should come up.

jstuxuhu0816
Level 1
Level 1

Do you need to use the media-type command?

Sent from Cisco Technical Support iPad App

charlhug
Cisco Employee
Cisco Employee

You likely need "negotiation auto" configured under this port, as many devices have autonegotiation enabled by default but the ASR9000 does not. The "media-type" command is not present on the ASR9000 as it's used to switch between SFPs and fixed copper ports - not for copper SFPs.

For the "Negotiation auto", do you mean for 1000M interface, since the 10G interface is alwasy force-up.

Try to configure this command under the interface :

"transceiver permit pid all"

mostakimulhuq
Level 1
Level 1

Thank Michalis.

I have applied your command and it is working.

Thanks very much for your co-operation.

Regards,

Shuvo

hi , i have same problem with 1G ports on my asr9010 , both with SFP-T transc and with 1000BASE-SX SFP

Pls check following link about transceivers support:

https://supportforums.cisco.com/t5/service-providers-blogs/asr9000-policy-3rd-party-optics/ba-p/3106940

 

Niko

HTH,
Niko

i'm not able to bring up 1gb copper ports on my asr9010 , linecard is A9K-40GE-TR SFP type is SFP-GE-T . i did put the following commands under every interfaces:

transceiver permit pid all

negotiation auto

service unsupported-transceiver

 

without success. Can somebody help me?

Hi Riccardo,

The best way is to open the TAC case to verify it in detail. Here we can check basics if you provide output of
show pfm loc all
"show controller Gig... all" -- put the correct port number
show log

Have you also made sure that there are no L1 issues on the line itself? Does the interface come with loopback internal?

Niko
HTH,
Niko

Hello , here attached the show commands required.

 

Hi RIccardo,

 

Thanks for the logs. I see that SFP is supported by the system so problem is different from what is discussed above:

 

Pluggable Compl.    : (Service Un) - Compliant
Pluggable Type Supp.: (Service Un) - Supported
Pluggable PID Supp. : (Permit All) - Supported

 

We can see that link stays down as no incoming signal detected:

 

H/W Link Defects    : (0x0000000000000038)  HW_LINK SFP_PHY_LINK LASI  ------ loss of signal

 

Also supported by this:

"Down (Reason: Link loss or low light"

 

This can identify the problem on:

- cable

- remote side

- transceiver itself

 

Best course of action will be:

- Open TAC case to verify it

- check cable

- Try to use any other know good transceiver in same port

- Try to use any other know good transceiver on remote side

- Change port on either side of this link

 

 

HTH

Niko

HTH,
Niko
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: