cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1579
Views
0
Helpful
7
Replies

Reseting Password for 7604 Router

sly007
Level 1
Level 1

I have tried to reset the password for 7604 but it is not working.

At the rommon mode, i input 0x2142, and then reset.

It reloads and keeps asking for password.

Please help                  

1 Accepted Solution

Accepted Solutions

Please take the time to read ALL the document that I've  linked before, to the part that says:

The boot sequence is different on the Catalyst 6500/6000 and Cisco 7600 that run Cisco IOS System Software than the Cisco 7200 Series Router because the hardware is different. After you power-cycle the box, the switch processor (SP) boots up first. After a short amount of time (approximately 25 to 60 seconds) it transfers console ownership to the route processor (RP (MSFC)). The RP continues to load the bundled software image. It is crucial that you press Ctrl-brk just after the SP gives over control of the console to the RP. If you send the break sequence too soon, you end up in the ROMMON of the SP, which is not where you should be. Send the break sequence after you see this message on the console:

00:00:03: %OIR-6-CONSOLE: Changing console ownership to route processor


After this point, the password recovery is the same as a normal router.

View solution in original post

7 Replies 7

paolo bevilacqua
Hall of Fame
Hall of Fame

System Bootstrap, Version 8.5(4)

Copyright (c) 1994-2009 by cisco Systems, Inc.

Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory

Autoboot executing command: "boot bootdisk:s72033-ipservices_wan-mz.122-33.SXH8b

.bin"

Loading image, please wait ...

Initializing ATA monitor library...

Self extracting the image... [OK]

Self decompressing the image : #################################################

################################################################################

############################# [OK]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, s72033_sp Software (s72033_sp-IPSERVICES_WAN-M), Version 12.

2(33)SXH8b, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 14-Sep-11 12:31 by prod_rel_team

Image text-base: 0x40101328, data-base: 0x41C6F330

00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging out

put.

00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for this switch

00:00:09: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging

output.

00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure consol

e debugging output.

Firmware compiled 13-Aug-10 11:12 by integ Build [100]

00:00:09: %OIR-SP-6-CONSOLE: Changing console ownership to route processor

System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2009 by cisco Systems, Inc.

Cat6k-Sup720/RP platform with 1048576 Kbytes of main memory

Download Start

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Download Completed! Booting the image.

Self decompressing the image : #################################################

################################################################################

################################################################################

###################### [OK]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICES_WAN-M), Version 12.

2(33)SXH8b, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 14-Sep-11 12:26 by prod_rel_team

Image text-base: 0x40101328, data-base: 0x42C30090

cisco CISCO7604 (R7000) processor (revision 2.0) with 983008K/65536K bytes of me

mory.

Processor board ID FOX1516G2U9

SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache

Last reset from s/w reset

1 Virtual Ethernet interface

72 Gigabit Ethernet interfaces

1917K bytes of non-volatile configuration memory.

8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).

Press RETURN to get started!

User Access Verification

Username:

Flowmask is MODIFIED to interface and full flow

% Username:  timeout expired!

And where is the confreg setting part ?

Forgive me, it was omitted,

Here is the full log:

monitor: command "boot" aborted due to user interrupt

Exit at the end of BOOT string

rommon 1 >

rommon 1 >

rommon 1 >

rommon 1 >

rommon 1 >

rommon 1 > confreg 0x2142

rommon 2 > set

PS1=rommon ! >

LOG_PREFIX_VERSION=1

BOOT=bootdisk:s72033-ipservices_wan-mz.122-33.SXH8b.bin,1;

RET_2_RTS=20:37:36 UTC Tue May 22 2012

SLOTCACHE=cards;

TYFIB_BLOCK_ALLOC=

NT_K=0:0:0:0

BSI=0

RET_2_RCALTS=

ACL_DENY=0

PF_REDUN_CRASH_COUNT=0

RANDOM_NUM=1126521762

?=0

rommon 3 > confreg 0x2102

You must reset or power cycle for new config to take effect

rommon 4 > set

PS1=rommon ! >

LOG_PREFIX_VERSION=1

BOOT=bootdisk:s72033-ipservices_wan-mz.122-33.SXH8b.bin,1;

RET_2_RTS=20:37:36 UTC Tue May 22 2012

SLOTCACHE=cards;

TYFIB_BLOCK_ALLOC=

NT_K=0:0:0:0

BSI=0

RET_2_RCALTS=

ACL_DENY=0

PF_REDUN_CRASH_COUNT=0

RANDOM_NUM=1126521762

?=0

rommon 5 > confreg 0x2142

You must reset or power cycle for new config to take effect

rommon 6 > set

PS1=rommon ! >

LOG_PREFIX_VERSION=1

BOOT=bootdisk:s72033-ipservices_wan-mz.122-33.SXH8b.bin,1;

RET_2_RTS=20:37:36 UTC Tue May 22 2012

SLOTCACHE=cards;

TYFIB_BLOCK_ALLOC=

NT_K=0:0:0:0

BSI=0

RET_2_RCALTS=

ACL_DENY=0

PF_REDUN_CRASH_COUNT=0

RANDOM_NUM=1126521762

?=0

rommon 7 > reset

System Bootstrap, Version 8.5(4)

Copyright (c) 1994-2009 by cisco Systems, Inc.

Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory

Autoboot executing command: "boot bootdisk:s72033-ipservices_wan-mz.122-33.SXH8b

.bin"

Loading image, please wait ...

Initializing ATA monitor library...

Self extracting the image... [OK]

Self decompressing the image : #################################################

################################################################################

############################# [OK]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, s72033_sp Software (s72033_sp-IPSERVICES_WAN-M), Version 12.

2(33)SXH8b, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 14-Sep-11 12:31 by prod_rel_team

Image text-base: 0x40101328, data-base: 0x41C6F330

00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging out

put.

00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for this switch

00:00:09: %SYS-SP-3-LOGGER_FLUSHING: System pausing to ensure console debugging

output.

00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure consol

e debugging output.

Firmware compiled 13-Aug-10 11:12 by integ Build [100]

00:00:09: %OIR-SP-6-CONSOLE: Changing console ownership to route processor

System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2009 by cisco Systems, Inc.

Cat6k-Sup720/RP platform with 1048576 Kbytes of main memory

Download Start

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Download Completed! Booting the image.

Self decompressing the image : #################################################

################################################################################

################################################################################

###################### [OK]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICES_WAN-M), Version 12.

2(33)SXH8b, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Wed 14-Sep-11 12:26 by prod_rel_team

Image text-base: 0x40101328, data-base: 0x42C30090

cisco CISCO7604 (R7000) processor (revision 2.0) with 983008K/65536K bytes of me

mory.

Processor board ID FOX1516G2U9

SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache

Last reset from s/w reset

1 Virtual Ethernet interface

72 Gigabit Ethernet interfaces

1917K bytes of non-volatile configuration memory.

8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).

Press RETURN to get started!

User Access Verification

Username:

Flowmask is MODIFIED to interface and full flow

% Username:  timeout expired!

Please take the time to read ALL the document that I've  linked before, to the part that says:

The boot sequence is different on the Catalyst 6500/6000 and Cisco 7600 that run Cisco IOS System Software than the Cisco 7200 Series Router because the hardware is different. After you power-cycle the box, the switch processor (SP) boots up first. After a short amount of time (approximately 25 to 60 seconds) it transfers console ownership to the route processor (RP (MSFC)). The RP continues to load the bundled software image. It is crucial that you press Ctrl-brk just after the SP gives over control of the console to the RP. If you send the break sequence too soon, you end up in the ROMMON of the SP, which is not where you should be. Send the break sequence after you see this message on the console:

00:00:03: %OIR-6-CONSOLE: Changing console ownership to route processor


After this point, the password recovery is the same as a normal router.

THANK YOU SOOOOOOOOOOOO MUCHHHHHHHHHHHHHHH!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

IT WORKED ! ! ! ! ! .

Thank you, once again.

Thank you for the nice rating and good luck!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card