cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
8195
Views
0
Helpful
12
Replies

Cisco Jabber for Windows can place Point to Point Video Call but can't place Multiparty Video Call

Hi,

                  

I have CUCM 8.6.2.21900-5 and Presence 8.6.4 and I have install Cisco Jabber for Windows ( CiscoJabber-Install-ffr.9-0-1.zip ) in 4 PCs .

We can place Point to Point Video Call but can't place Multiparty Video Call,

When we add 3rd party in Point to Point Video Call that time conference call automatically converts into Audio Call only.

Regards,

Shashank

12 Replies 12

Michael Boscia
Level 4
Level 4

Do you have a video MCU or an ISR G2 with PVDMv3 DSPs with video conferencing resources defined in your MRG and MRGL that are assigned to the device pool that your Jabber devices are assigned to?

We dont have any external video MCU or an ISR G2 with PVDMv3.

Is it required for multiparty video call ?

Can we configure CUCM to do multiparty video without MCU or ISR ?

Without an ISR or an MCU or some sort of a bridging service, the answer is no.

Sent from Cisco Technical Support iPhone App

Hi Michael,

I do have an ISR G2 router with pvdm3 configured as homogeneous.

I verified that the DSPs are being used when

I try to do the video conferencing, however

I cannot videoconference 3 devices.

Please note the the videoconference works

With my 9971 phones.

I'm using codec h264 cif-30-740.

Do you suspect a codec issue for jabber?

What is the current official position on this?

I am interested in positioning Jabber for Windows Clients forming Video teleconferences using only PVDM3s on ISR-G2's.

From what I have read, it looks like this is supported.

I also find some inconsistent documentation about  'lecture mode', where one doc says its supported, but the other says its  not.  Are we limited to only active speaker via CUCM control?  What are  the rules on content sharing inside a video conference? 

No BFCP screen sharing support for PVDM3.
Active speaker presentation.

Add the resource the UCM just like an Xcode or conf bridge.

Sent from Cisco Technical Support iPhone App

Were you able to figure this out?  I've yet to find any documentation officially noting support for Jabber on the PVDM3's, but it "sounds" like it should work OK via MRGL.

Am experiencing  the same issue; I can make point-to-point video calls on Jabber but having issues making video conference calls even after I configured video conference bridge via an ISR router and also have an MCU set-up as well.

 

Any ideas on what to check next?

I even created a separate profile for 720p video which jabber uses as shown below, but still no go.

Has anyone been able to get Jabber for windows video conference working?

dspfarm profile 2 conference video homogeneous 

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

codec h264 720p frame-rate 30 bitrate 2mbps

maximum conference-participants 8

maximum sessions 4

associate application SCCP

danielgarzon
Level 1
Level 1

Hi,

Are there any config example?

I have a MCU and I want to integrate Jabber and MCU for Multiparty Video Call.

Thanks

I have the same problem for making multi party video call using CUCM 7.1.5, Meeting Place 8.6 as conference bridge and cisco Jabber 9.2.3.

Point to point video is ok but when the third party is added it becomes a audio call. Any suggestions Please??

Thank you.

Ismail Egieya
Level 1
Level 1

Hi,

 

Just wondering if you managed to fix this problem?

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: