TelePresence EX60 with CUCM 8.5 - How to Integrate??

Answered Question
Dec 13th, 2012

Good morning people,

I'm building a lab with CUCM 8.5 and Presence Server 8.5

I'll install the Cisco TelePresence EX60, and I wonder how I do the integration with CUCM.

Have any need to install additional server? You simply add a SIP device in CUCM?

Can someone help me??

Thank you

Bruno

I have this problem too.
0 votes
Correct Answer by Marius Nedregaard about 2 years 8 months ago

Hi.

You would need to have CUCM 8.6 in order to utlize the full potential of the CUCM / EX60 integration. You register the device directly to the CUCM.

I would recommend you to have a look at this guide after you have proceeded with updating your lab.

http://www.cisco.com/en/US/docs/telepresence/endpoint/codec-c-series/tc5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.pdf

I have attached a screenshot showing how it should look in the device overview page.

Thanks

//Marius

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Correct Answer
Marius Nedregaard Thu, 12/13/2012 - 06:41

Hi.

You would need to have CUCM 8.6 in order to utlize the full potential of the CUCM / EX60 integration. You register the device directly to the CUCM.

I would recommend you to have a look at this guide after you have proceeded with updating your lab.

http://www.cisco.com/en/US/docs/telepresence/endpoint/codec-c-series/tc5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.pdf

I have attached a screenshot showing how it should look in the device overview page.

Thanks

//Marius

brunofalco Mon, 12/17/2012 - 05:02

Hi Marius,

Sorry for the delay, thanks for your help ...

I made an installation of CUCM 8.6 (1) and could register it successfully!

Taking advantage, you know the Cisco TelePresence VX Clinical Assistant??

I need to register it in CUCM 8.6 ... but also do not think much documentation for it ... knows something that can help me?

Tks

Bruno

brunofalco Mon, 12/17/2012 - 11:03

Hello Andriy,

See the options that I have to create this endpoint.

Have you tested it with some, but without success.

Currently hooked up a router to use as a gatekeeper, also without success.

I added a Gatekeeper in CUCM and a trunk, could not also, see the results:

The IP is 20.20.0.10 of CUCM.

NO VX Clinical I get the following information: "Failed Rejeitado.Encoding RRQ"

azeem.haider Wed, 07/16/2014 - 06:06

Hi Guyz...

i am trying to Register Cisco VX Clinical Assistant on CUCM 9.

which phone type do i have to Select...?

I have tried Cisco TelePresence Quick Set (C20) but it is not registering.

But when i open the webpage of the codec in VX clinical Assistant it shows EX90 codec.

 

 

brunofalco Wed, 07/16/2014 - 06:56

 

Good day, 

At the time I was using version 8.6 of the CUCM. 
As there were no way to register VX Clinical, I needed to configure a Gatekeeper, and register it. 

That way worked. 
Today, in version 9 I do not know if it's possible.

Regards,

Bruno

Ravi Yadav Wed, 07/16/2014 - 07:14

Now days the VX clinical is coming with an SX20 Codec

hardware version 1.2

and it supports native registration 

use Sx20 instead of c20 .

what is the version on sx20 ?

 

 

Regards

Ravi kr.

Actions

This Discussion

Related Content